SEARCH

Found 1847 related files. Current in page 1

vacuum hose routing diagram 1996 rav4

VW Amarok - Body Harness.pdf - Hayman Reese

For P/No: 04998 & 04999 only. 1. In the engine bay, disconnect the negative and positive battery terminals. 2. Remove the vehicle battery (1) by first removing any fasteners. 3. Locate the vehicle grommet behind the battery cavity area. 4. Pierce a hole in the vehicle grommet. Note: Do not connect the harness to the battery at this point. Issue Date 27-09-10 For P/No: 04997 only. 5. In the engine bay, locate the vehicle battery (1). 6. Route the body harness (2) down through to the chassis. Note: Do not connect the harness to the battery at this point. 7. Route the power input harness (1) from the engine bay down through to the chassis, following the path of the brake and fuel lines. For P/No: 04997 & 04999 only. 8. Following the diagram on the right, house the two power & ground input harness female terminals (4) into the mating connector (3). 9. Connect the power input harness connector (3) to the body harness mating connector. Issue Date 27-09-10 For P/No: 04998 only. 10. Following the diagram on the right, house the three power & ground input harness female terminals (4) into the mating connector (5). 11. Connect the power input harness connector (5) to the body harness mating connector. 12. Route the body harness (1) along the LHS chassis rail, following the path of the blue vehicle harness towards the rear of the vehicle. 13. Route the body harness (1) along the rear of the vehicle towbar towards the towbar mounting bracket. Issue Date 27-09-10

Trolley Jacks - Supplier Guide - ACCC

Australian Competition and Consumer Commission 23 Marcus Clarke Street, Canberra, Australian Capital Territory, 2601 © Commonwealth of Australia 2013 This work is copyright. In addition to any use permitted under the Copyright Act 1968, all material contained within this work is provided under a Creative Commons Attribution 3.0 Australia licence, with the exception of: • the Commonwealth Coat of Arms • the ACCC and AER logos • any illustration, diagram, photograph or graphic over which the Australian Competition and Consumer Commission does not hold copyright, but which may be part of or contained within this publication. The details of the relevant license conditions are available on the Creative Commons website, as is the full legal code for the CC BY 3.0 AU licence. Requests and inquiries concerning reproduction and rights should be addressed to the Director, Internal Communication and Publishing Services, ACCC, GPO Box 3131, Canberra ACT 2601, or publishing.unit@accc.gov.au. Important notice The information in this publication is for general guidance only. It does not constitute legal or other professional advice, and should not be relied on as a statement of the law in any jurisdiction. Because it is intended only as a general guide, it may contain generalisations.

renault megane rs250 dump valve installation - Forge Motorsport

Tools needed: 10mm socket and 3/8” ratchet 10mm ratchet spanner 7mm hose clamp driver 1. Open the bonnet and grasp both sides of the engine cover, then sharply pull upwards to remove it from the rubber grommets underneath. 2. Remove the breather assembly as shown below, by pushing the black retaining clip in on the gray fitting at the front, the yellow retainer in on the black fitting at the back, and simply pulling the rubber hose off the cam cover. Rear fitting Rubber hose Front fitting 3. Loosen the jubilee clip on the bottom of the noise generator. Move the gearbox breather out of the way, and undo the now accessible 10mm bolt on the top of the noise generator. This 10mm nut needs to be undone 4. Remove the end of the noise pipe from the firewall by squeezing the tabs top and bottom and wiggling the pipe out. 5. You can now remove the lower 10mm bolt holding the noise generator to the side of the engine using a ratchet spanner from the front or ¼” drive ratchet from the back, and remove the noise generator from the car. Lower 10mm bolt 6. Using the supplied silicon hose, cut a short length (50-75mm) from the end, then fit this and the remainder of the hose to the tee piece as shown. To stock rubber hose To valve To stock tee piece 7. Locate the vacuum feed to the standard valve as shown below. Remove the rubber feed to the valve from the stock tee piece, then fit our tee piece in between.

Several of the best-rated best vacuums To assist you save time frame

In Vacuum Review Zone site there might be the right product should you wish to obtain vacuum machine that will help you in washing your house.

Benefits of a Vacuum-Powered Home Wheelchair Lift

Pneumatic Vacuum Elevators describes the installation and advantages of vacuum powered home wheelchair lifts for new and existing homes.

Product Guide - Sonos
by Ijimura 0 Comments favorite 4 Viewed Download 0 Times

No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including but not limited to photocopying, recording, information retrieval systems, or computer network without the written permission of Sonos, Inc. SONOS and all other Sonos product names and slogans are trademarks or registered trademarks of Sonos, Inc. SONOS Reg. U.S. Pat. & Tm. Off. Sonos products may be protected by one or more patents. Our patent-to-product information can be found here: sonos.com/legal/patents iPhone®, iPod®, iPad® and iTunes® are trademarks of Apple Inc., registered in the U.S. and other countries. Windows® is a registered trademark of Microsoft Corporation in the United States and other countries. Android® is a trademark of Google, Inc. MPEG Layer-3 audio decoding technology licensed from Fraunhofer IIS and Thomson. Sonos uses MSNTP software, which was developed by N.M. Maclaren at the University of Cambridge. © Copyright, N.M. Maclaren, 1996, 1997, 2000; © Copyright, University of Cambridge, 1996, 1997, 2000. All other products and services mentioned may be trademarks or service marks of their respective owners. March 2014 ©2004-2014 by Sonos, Inc. All rights reserved. SONOS DOCK • Allows you to play your favorite music from an iPod® or iPhone® on a Sonos system—all throughout your home. The DOCK is compatible with*: • iPod touch (1st, 2nd 3rd, and 4th generation) • iPod classic • iPod nano (3rd, 4th, 5th and 6th generation) • iPhone 4, iPhone 4S, iPhone 3GS • iPhone 3G, iPhone • Charges while it’s seated in the DOCK. The DOCK supports 1 Amp charging, the latest specification from Apple®. • Great for parties—simply have your friends dock their iPod or iPhone for play back on your Sonos system. * For the latest system requirements or compatible audio formats, go to http://faq.sonos.com/specs.

Steering, Suspension, and Driveline Basics (with How Lift ... - Meetup

Throughout this article I will address many basics of your vehicle’s steering, suspension, driveline, tires, and wheels. I did not intend this to be a “how to” manual with step by step instructions. It will simply illustrate the concepts. I’ll start with the lift and explain what it did to your steering, suspension, and driveline one aspect at a time. NOTES ABOUT THE ILLUSTRATIONS: 1) most are “spring under” leaf spring suspension, 2) non-pertinent parts are omitted for clarity, 3) many examples are exaggerated for illustration, and 4) most concepts illustrated also apply to spring over and coil/link suspensions. To cover the differences, I added a separate coil and link suspensions topic. Ready? OK, let’s get started. You lifted your Jeep and now it wanders all over the road and it vibrates too. What happened? Well, you just changed a lot of the vehicle’s geometry (probably without knowing it). Here’s a diagram of a stock Jeep and the proper angles. Your caster angle should be between 4 and 8 degrees positive. This caster angle creates an effect called mechanical trail. It’s the force that makes your wheels return to center. The caster angle shown below is close to stock. The point that the steering axis (black line) intersects the ground to the point to where the rotational axis touches the ground forms the points to measure your caster angle. You can best measure the caster angle from the top of the upper ball joint.

1 TON FOLDING ENGINE STAND - Harbor Freight Tools

1 TON FOLDING ENGINE STAND Model 47304 ASSEMBLY AND OPERATING INSTRUCTIONS ® 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our Web site at http://www.harborfreight.com Copyright © 2002 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools . For technical questions and replacement parts, please call 1-800-444-3353 Specifications Engine Stand Capacity Assembled Dimensions Folded Dimensions Engine Turn Capacity Main Post Height 1 Ton (2000 Lbs.) 42” L x 36” W x 34” H 17” L x 22-1/2” W x 40” H 360 Degrees 32-1/2” Save This Manual You will need the manual for the safety warnings and precautions, assembly instructions, operating and maintenance procedures, parts list and diagram. Keep your invoice with this manual. Write the invoice number on the inside of the front cover. Keep the manual and invoice in a safe and dry place for future reference. Safety Warnings and Precautions WARNING: When using product, basic safety precautions should always be followed to reduce the risk of personal injury and damage to equipment. Read all instructions before using this product! 1. Avoid working alone. If an accident happens, an assistant can bring help. 2. Keep work area clean. Cluttered areas invite injuries. 3. Observe work area conditions. Don’t expose to rain. Keep work area well lighted. 4. Keep children away. Children must never be allowed in the work area. Do not let them near the Stand. 5. Store idle equipment. When not in use, the Stand must be stored in a dry location to inhibit rust. Always lock up tools and keep out of reach of children. 6. Dress properly. Do not wear loose clothing or jewelry as they can be caught in moving parts. Protective, electrically nonconductive clothes and nonskid footwear are recommended when working. Wear restrictive hair covering to contain long hair. 7. Use eye and ear protection. Always wear ANSI approved impact safety goggles. 8. Do not overreach. Keep proper footing and balance at all times. Do not reach over or across electrical cables or frames. 9. Maintain Stand with care. Inspect Stand, and if damaged, have it repaired by an authorized technician. SKU 47304

obd ii drive cycle obd - OBD Clearinghouse

PURPOSE During the OBD--II drive cycle, the OBD--II system checks each emission control system by monitoring it for proper operation. It is necessary to run the OBD--II drive cycle: D After repairing an affected vehicle to eliminate a fuel--related or emission--related diagnostic trouble code (DTC). The OBD--II drive cycle will monitor the affected emission system and confirm that the repair was successful. D If the vehicle’s I/M test (“smog check”) results indicate that the OBD--II Readiness Monitors are “incomplete.” Readiness Codes for 1996--98 models are not set to “complete” until all required monitors have gone through one complete monitor cycle. OBD--II monitors could identify a failure. After that, Readiness Codes are set to “complete” after each individual monitor has been completed. Effective January 2, 2001, the U.S. Environmental Protection Agency (EPA) will require that vehicles must have all OBD--II Readiness Codes “complete” at the time of an I/M test. This bulletin contains: S OBD--II drive cycle procedure for 1996-97 affected vehicles only (Refer to the appropriate service manual for 1998 and later model OBD--II drive cyle procedures.) S Warranty claim information for OBD--II drive cycle on all affected vehicles. NOTE: On 1996--97 V6 models, after all Readiness codes are complete, turning the ignition off will cause all the Readiness status readings to show incomplete (“INCMP”). This may require that an I/M test be performed before the ignition key is turned off.

3.0 L V6 - VINS [H,J,K] - dairally.net

Removal (Diamante) 1) Remove hood. Drain cooling system. Remove radiator. Release fuel system pressure. See FUEL PRESSURE RELEASE. Disconnect negative battery cable. Drain engine oil and transaxle oil. Remove front exhaust pipe. Remove transaxle assembly. See appropriate CLUTCHES or TRANSMISSION SERVICING article. 2) Disconnect accelerator cable, brake booster vacuum hose, fuel supply and return lines, and heater hoses. Disconnect EGR temperature sensor (if equipped). Unplug vacuum hose connector. Remove drive belts. Remove power steering pump and A/C compressor, leaving hoses attached. 3) Unplug all harness connectors. Remove bolt from body ground connection. Disconnect alternator wiring inside relay box. Remove relay box and engine wiring harness connection. On models with ABS, remove radiator overflow tank and bracket. 4) Attach engine hoist. Raise engine enough to take weight from mounts. Remove engine mount bracket. Remove damper. Remove rear roll stopper bracket mount bolt. Remove front roll stopper bracket mount bolt. Carefully lift engine from car. Installation (Diamante) To install, reverse removal procedure. Install engine mount bracket so that arrow points away from engine, toward body. Install new "O" rings on fuel lines. Install new exhaust gaskets and nuts. Adjust throttle cable. See TORQUE SPECIFICATIONS TABLE at the end of this article. Replenish fluids. CAUTION: DO NOT allow foreign material into turbocharger air intake hoses or pipes.

« previous  123456789