SEARCH

Found 1022 related files. Current in page 29

ukuran box salon 18 inch

TOYOTA CAMRY LE / SE / XLE 2012- DUAL SEAT ... - Rostra

TOYOTA CAMRY LE / SE / XLE DUAL SEAT HEATER KIT STOP: Damage to the vehicle may occur. Do not proceed until process has been complied with. OPERATOR SAFETY: Use caution to avoid risk of injury CRITICAL PROCESS: Proceed with caution to ensure a quality installation. GENERAL PROCESS: This highlights specific processes to ensure a quality installation. TOOLS & EQUIPMENT: This calls out the specific tools and equipment required for this process VEHICLE PROTECTION: This calls out for protection of vehicle required for this process Conflicts DUAL SEAT HEATER KIT Section II –Installation Pre-Installation Suggestions 1. Disconnect the negative battery cable and wait for 3 minutes before beginning installation, to avoid unintended air bag deployment. Note and record any anti-theft radio codes prior to disconnecting. Figure 1 Figure 1 2. If vehicle is in Electronics work area, proceed to step 1 page 4. If vehicle is in Leather shop, proceed to next section “Install Heating Elements”. Install Heating Elements 1. Remove seats from vehicle per vehicle’s service manual and place on a clean work surface. 2. Remove seat covers per vehicle’s service manual. 3. Caution: The heating elements must be installed wrinkle-free. 4. Obtain the back heating element. Remove the protective layer from the element’s double sided tape and place it onto the seat back foam roughly centered on the foam from side to side with the top of the element just below the transverse listing (tie bar trench). Figure 2 5. Route the element wiring harness down to the bottom of the seat back, inboard of the hinge cover and under the seat. Note: Factory leather and cloth 6. Repeat the process above for the seat cushion, laying the heating element transversely such that it does not interfere with the horizontal listings. Figure 3 7. Secure the seat harnesses to the tie down bar and run down the side listing to the back of the seat, then down. Re-attach seat covers. Figures 4-5 8. Replace the driver and passenger seats into the vehicle. Connect the seat element connectors to the main harnesses. Secure the harness with wire ties and allow adequate slack to prevent damage during seat adjustment. TOYOTA CAMRY LE / SE / XLE DUAL SEAT HEATER KIT Section II –Installation Install Heating Elements (cont’d) 9. Make sure vehicle floor-pan is clear and carefully re-locate seat into vehicle. 10. Ensure all connectors under seat have been properly connected and secured with wire ties, and that nothing will be damaged upon seat movement. 11. Install seat bolts and torque per service manual. 12. Reconnect battery cable(s). Torque 10mm bolt to 48 inch-pounds. Re-enter any theft deterrent information, if applicable...

LG Chocolate Touch VX8575 Spotted at Verizon - Softpedia News

By: Ionut Arghire, Mobile Editor 26 October 2009 LG Chocolate Touch VX8575 Spotted at Verizon Should be launched come November 5 LG Chocolate Touch VX8575 phone Arena South Korean mobile phone maker LG Electronics unveiled a few months ago plans to come to the market with a series of new Chocolate mobile phones, among which we already saw the BL40 New Chocolate device, and some even expected it to come to the US market via Verizon Wireless. The carrier was said to soon launch a Chocolate phone, yet it seems that the Chocolate Touch VX8575 will be this handset, and not the elongated BL40. The LG Chocolate Touch VX8575 was spotted around the web a few times before, and now the guys over at phone Arena have managed to learn the full specifications of the device, and have also reported that it can be already seen in Verizon's system. According to the news site, enthusiasts should expect for this phone to become available for purchase starting with November 5, though the release date is not yet official, and details on its pricing have not emerged either. What the Chocolate Touch VX8575 should deliver to users includes a 3.0-inch TFT display that boasts a 400 x 240 pixel resolution and support for 262K colors, along with a 3.2-megapixel photo snapper with fixed focus, a 3.5mm headset jack, Dolby Mobile, 1GB of internal memory, and a microSDHC memory card slot with support for up to 16GB of additional storage space. Other specs of the phone also include MP3 Player and FM Radio Receiver, multitasking capabilities, HTML Browser, support for VCast Video/Music and VZ Navigator, as well as for EVDO Rev 0 connectivity. The LG Chocolate Touch VX8575 is said to measure 4.30 x 2.20 x 0.47 inches and weigh 4.23oz, while shipping to the market with Software Version VX857V04 on board. According to phone Arena, the handset will be activated only with the Nationwide calling plans, yet there are no details on whether a data plan will be required or not. While no details on the phone's pricing have emerged so far, the news site suggests that one should expect it to cost under $100, which doesn't seem too much for such a device...

BlackBerry Z10 - Fact-magazine.com
by 6uest 0 Comments favorite 54 Viewed Download 0 Times

TECHNOLOGY scrolling up from the bottom of the screen simply minimises the current app, where you can either close it, or keep it open and scroll right to the home screen. It boasts a similar app grid display with sliding panels – however, it differs slightly in that when you open an app, or several, you have to manually close them rather than simply exiting back to the home screen. This might be good for people who want to have several tasks on the go, and don’t want to have to exit and re-enter an app whenever they want to do something else. Office document software comes with the phone; you can edit and view .docs, .ppt, .xls files, etc., as well as Adobe Reader, further strengthening BlackBerry’s status as the preferred choice for business users. You’ll see this even further when you look at the apps that come standard with the phone, such as Dropbox, Newsstand, LinkedIn, and so on. Another good app is Print To Go, where you can wirelessly An exclusive review of RIM’s new smartphone... BlackBerry Z10 There has been a great deal of hype and fanfare over the launch of the new BlackBerry Z10, with celebrities like Stephen Fry singing its praises before it was even launched globally, and Alicia Keys signing up as a brand ambassador. The global marketing campaign has been colossal, with pre-launches and sneak previews building momentum ahead of the massive global launch last month. We were lucky enough to be invited over to Dubai to take part in said launch, which was co-ordinated via video stream with launches in the US and Asia. Most impressive, perhaps, was the goodie bag containing the Z10 itself, and everyone in the office was scrambling to play with it as soon as we returned. So, what are our impressions? Well, let’s start by looking at the specs. The Z10 boasts a 768x1280 pixel 4.2-inch multitouch display, putting it slightly ahead of the iPhone 5. It boasts 16GB of internal storage, with 2GB RAM. However, storage can be upgraded to 64GB with a MicroSD card, unlike other smartphones,...

Download Full Brochure - Luxury AutoMax

Luxury AutoMax 2116 Lincoln Way East Chambersburg, PA 17202 “It is the customer's sole responsibility to verify the existence and condition of any equipment listed. Neither the dealership nor eBizAutos is responsible for misprints on prices or equipment. It is the customer's sole responsibility to verify the accuracy of the prices with the dealer. Pricing subject to change without notice.” Powered by eBizAutos Luxury AutoMax 2116 Lincoln Way East Chambersburg, PA 17202 Contact: Mike Ahn Vehicle Description: CLEAN CARFAX AND CARFAX CERTIFIED & AUTOCHECK CERTIFIED he 2006 Scion tC Release Series “It is the customer's sole responsibility to verify the existence and condition of any equipment listed. Neither the dealership nor eBizAutos is responsible for misprints on prices or equipment. It is the customer's sole responsibility to verify the accuracy of the prices with the dealer. Pricing subject to change without notice.” Powered by eBizAutos 2.0 will come in a brilliant Blue Blitz Mica. This limited edition tC features a stainless steel mesh upper and he 2006 Scion tC Release Series 2.0 will come in a brilliant Blue Blitz Mica. This limited edition tC features a stainless steel mesh upper and lower front grille and 17-inch alloy wheels that come with a satin metallic finish. The tC's only factory option, front seat-mounted side airbags and front and rear side curtain airbags, is standard equipment on the R.S. 2.0. Inside, the tC's front and rear seats are trimmed with black Alcantara, a suede-like material that provides passengers better friction grip and is more commonly found in luxury or performance vehicles and on aftermarket racing seats. The tC R.S. 2.0 comes standard with a Pioneer Premium AM/FM/CD audio system with iPod connectivity and color-changing LED display. A Pioneer six-inch subwoofer with 35-watt maximum power complements the upgraded head unit and is tuned specifically for the tC. This compact subwoofer is mounted in the under-floor storage area, keeping it out of sight and leaving the cargo floor clear. This tC also is equipped with XM Satellite Radio and comes with a paid three-month subscription, wherever XM service is available. An individually numbered brushed stainless steel badge completes the uniqueness of this vehicle. Only 2,600 units of the tC Release Series 2.0 will be built. The tC Release Series 2.0 model will carry a manufacturer's suggested retail price (MSRP) of $1,960 over the base price of the tC. The base MSRP for the tC starts at $16,300. A 2006 tC Release Series 2.0 will be on display in the Scion booth at the New York International Auto Show...

Barber chairs,Beauty Furniture
by timloc 0 Comments favorite 52 Viewed Download 0 Times

Salon Furniture with Style With some of the world's finest salon furniture available; Dream In Reality Group is the one-stop-shop for the highest quality, fashion and competitively priced salon accessories, furnitures.

FLYWHEEL NUT REMOVAL
by Prezta 0 Comments favorite 99 Viewed Download 0 Times

Bolt Torque Spec Chart for Chevy Small Block Chevy IMPORTANT NEVER wedge a screw driver, or pry lever into the flywheel to prevent the flywheel from rotating while you try to remove the nut. You will ruin the coils or flywheel or both. Electrex does not warranty any parts damaged by customer error. Note: Exectrex USA cannot be held liable for any damage or injury to persons or property during any service or repair. HOW DO YOU GET THE NUT OFF? Stator WASHER FLYWHEEL NUT TYPICAL FLYWHEEL ASSEMBLY - FOR REFERANCE ONLY FLYWHEEL METAL HAMMER BOX END WRENCH REMOVING THE NUT WITHOUT AN AIR WRENCH You will need to remove the locking nut on the outside of the flywheel. This can be accomplished by using either an air torque wrench, or our suggested manual method. Air Wrench Method Grasp and hold the flywheel with one hand, and use an air wrench to loosen and remove the flywheel nut. Manual Method Grasp and hold the flywheel with one hand, while using a box end wrench nested on the nut and keep the wrench snug between your fingers. Then take a metal hammer, and hit the other end of the wrench. You want to hit it with a quick snap of the wrist, while you are grasping the flywheel firmly with your other hand. Note: it may take a few good hits to loosen the nut. Note: While thismethod does work, we recommend using an air wrench. P U L L I N G F LY W H E E L S Remove the flywheel nut Note: You only need to screw the bolts in about 1/4 Inch. You will need to remove the locking nut on the outside of the flywheel. This can be accomplished by using either an air torque wrench, or our suggested manual method. If necessary, please review the instructions on how to perform this step. IMPORTANT NEVER wedge a screw driver, or pry lever into the flywheel to prevent the flywheel from rotating while you try to remove the nut. You will ruin the coils or flywheel or both. Electrex does not warranty any parts damaged by customer error. CRANKSHAFT BOLT BOLTS Note: Exectrex USA cannot be held liable for any damage or injury to persons or property during any service or repair. 3-Bolt Style Puller FLYWHEEL Screw in three bolts from puller side into the flywheel. Be sure that the bolts are seated flush with the puller backing plate. CHECK THE BACKING PLATE CLEARANCE: If the 3 bolts are screwed in too far on the backing plate of the flywheel puller, damage will occur to the stator/coils...

Styling units
by timloc 0 Comments favorite 48 Viewed Download 0 Times

Salon Furniture with Style With some of the world's finest salon furniture available; Dream In Reality Group is the one-stop-shop for the highest quality, fashion and competitively priced salon accessories, furnitures.

03 Suzuki Hayabusa Prototype - Motorsports Almanac

Suzuki Sport Hayabusa Prototype Road GT-car Based on the Formula Suzuki Hayabusa, Suzuki Sport has developed the "Hayabusa Prototype" a light weight sport car from the beginning considering running on public roads and it was shown to the world at 2002 Tokyo Auto Salon with Auto Asia.The concept called for a "Ultimate light weight sport car". To have superb handling is what we aimed for and the layout has been decided. With Suzuki Sport original steel tube + aluminum panel frame, "Suzuki GSX-R1300R Hayabusa" engine is installed in front midship and driven by rear wheel. Body is made from FRP using carbon fiber. Design was established by testing at moving belt type wind tunnel facility in Suzuki Sport factory to have excellent aerodynamics. Chassis and body uses fully original design (ex.suspensions) and Suzuki's genuine parts (ex. differential) in order to be low cost yet to have high original quality. The Hayabusa Prototype from Suzuki Sport. THE SUZUKI SPORT HAYABUSA PROTOTYPE www.suzukisport.com When people drove the Formula Suzuki Hayabusa at Suzuki One Make Race Series, everybody started saying "Wouldn't be great if we can drive this kind of car on the road?" That light weight sport car is what we gave the answer for. "Hayabusa Prototype" Based on Formula Suzuki Hayabusa, Suzuki Sport has developed from the beginning considering running on public roads and was shown to the world at 2002 Tokyo Auto Salon with Auto Asia.Concept "Ultimate light weight sport car" To have superb handling is what we aimed for and the layout has been decided.Hereby is what we aimed for. Super light weight Light weight on over hang part Equal weight distribution on all four wheels Short wheel base Low center gravity Minus lift aerodynamics Outline With Suzuki Sport original steel tube + aluminum panel frame, "Suzuki GSX-R1300R Hayabusa" engine is installed in front midship and driven by rear wheel. Body is made from FRP using carbon fiber. Design was established by testing at moving belt type wind tunnel facility in Suzuki Sport factory to have excellent aerodynamics. Chassis and body uses fully original design (ex. suspensions) and Suzuki's genuine parts (ex. differential) in order to be low cost yet to have high original quality. To give out much performance of motorcycle engine and handling, light weight was must. Frame was analyzed by help of Suzuki Motor Corporation to simulate crash test for the safety. To make the center gravity low, exhaust pipe is fitted on left side of the frame. Making the floor flat and up tail at the rear results ground effect which makes minus lift aerodynamics. Gull wing doors make easy access to the cockpit. Future plan The prototype which was presented at the show are not yet complete to run public road. At the moment, there is no plan made for further development, producing, and sales. SUZUKI SPORT Suzuki Sport Co.,Ltd. was established May 1st, 1986. They have currently 76 employees and Nobuhiro Tajima is the Chairman. The outline for the company : Overall planning, designing, manufacturing, and sales of competition, prototype, and ordinary cars and engines.Consulting business for planning, designing, manufacturing, and sales of competition and rdinary cars...

Lames & chaînes de tronçonneuse - ESF

Lames de débroussailleuse Brushcutter blades LAMES BEAVER BEAVER BLADES • Réduit les dommages causés aux arbres d'entraînement et aux têtes d'engrenage des débroussailleuses. • Réduit les contrecoups. • Affûtage prolongé de la chaîne comparativement aux lames comportant des dents. • Facile à affûter et à remplacer. Catalogue Pièces de Remplacement Replacement Parts •Reduces damages to drive shafts & gear heads on brushcutters. •Reduces kickback. •The chain stays sharp longer than saw tooth typeblade, is easily resharpened and easily Replaced. Scies à chaînes Scies à béton Coupe-herbe Débroussailleuses Grandes Coupes: Les lames Beaver sont vendues dans les dimensions 7,8,9,10 et 12 pouces, assez grandes pour se charger des plus gros problèmes de débroussaillage. Big Cuts: Beaver Blades come in 7, 8, 9, 10 and 12-inch sizes, big enough to handle toughest brushcutting problems. Coupes nettes: La lame Beaver se caractérise par une chaîne à coupe uniforme qui produit un trait de scie net et large, éliminant le blocage. Sur le terrain, la chaîne est facile à affûter ou remplacer. Smooth Cuts: The Beaver Blade features a smooth-cutting chain that produces a clean, wide kerf, eliminating binding. And in the field, the chain is easy to resharpen or replace.Lames & chaînes de tronçonneuse Chainsaw bars & chains Coupes faciles: Pour qu’elle soit fiable lorsque vous en avez besoin, la lame Beaver a été testée à 133 pour cent de la vitesse d’opération recommandée pour en assurer la qualité. Les chaînes de remplacement ont été soumises aux mêmes rigoureux standards. Easy Cuts: To make sure it works when you need it, every Beaver Blade is tested at 133 percent of recommended operating speed to ensure quality. Replacement chains are subjected to the same rigorous standards...

5 Importance of salon insurance

As an owner of a Salon it is important to get a salon insurance cover to deal with anything arising in the business.

 252627282930313233