Found 4878 related files. Current in page 1
[b] If clutch contact face is scored or worn, the flywheel may be refaced. [c] If clutch contact face is cracked, the flywheel must be replaced. NOTE: Do not remove more than 0.508 mm (0.020 in.) material from the flywheel. Maintain all of the radii when resurfacing. 2. Inspect the ring gear. [a] Check ring gear for excessively worn or damaged gear teeth. [b] If damaged gear teeth are detected, replace the ring gear. Refer to Section 1.15.3. 3. Inspect crankshaft and flywheel contact surface. [a] Check the butt end of the crankshaft and flywheel contact surface for fretting, brinelling, or burrs. See Figure 1-212. [b] Lightly stone the contact surface to remove any fretting, brinelling, or burrs. Figure 1-212 1.14.3 Crankshaft and Flywheel Mating Surfaces Installation of Flywheel Install the flywheel as follows: 1. Install two flywheel guide studs, J 36235, into two of the tapped holes in the crankshaft at the 3 and 9 o’clock position. 2. Attach the flywheel lifting tool and, using a chain hoist, position the flywheel in the flywheel housing. Align the flywheel bolt holes with the crankshaft bolt holes. All information subject to change without notice. (Rev. 2004) 6SE50 0403 Copyright © 2004 DETROIT DIESEL CORPORATION From Bulletin 2-50-04 1-261 1.14 FLYWHEEL NOTICE: A new scuff plate must be used whenever the flywheel is removed. Failure to replace the scuff plate may cause the flywheel bolts to loosen, even when torqued correctly. 3. Using a new scuff plate, install two bolts with International Compound #2® (or equivalent) through the plate 180 from each other. 4. Install the flywheel lock, J 36375–A. See Figure 1-195. 5. Remove the flywheel lifting tool and guide studs. 6. Apply International Compound #2® (or equivalent) to the threads and to the bolt head contact area (underside) of the remaining bolts. The bolt threads must be completely filled with International Compound #2® (or equivalent). Any excess must be wiped off. See Figure 1-213.
New flanged multi-point socket head bolts have been released to prevent the MBE 900 pilot bearing from walking out of the flywheel housing. The new bolts will replace two flywheel bolts, located 180 degrees from one another. KIT CONTENTS The MBE 900 Pilot Bearing Bolt Service Kit P/N: A9269900105, consists of the following parts, listed in Table 1: Part No. A9269900005 18SP666 Table 1 Qty. 2 1 Description Flanged Multi-point Socket Head Bolts Installation Instructions MBE 900 Pilot Bearing Retaining Bolt Service Kit (P/N: A9269900105) INSTALLATION PROCEDURE Use the following procedure to install the new flanged multi-point socket bolts: 1. Shut off engine and apply the parking brake, chock the wheels, disconnect vehicle battery power, and perform any other applicable safety steps. 2. Remove the transmission. 3. Remove clutch from flywheel. 4. Pull the crankshaft position sensor out of the flywheel housing about 8 mm (0.32 in.). 5. Remove the end cover from the flywheel housing and install the engine barring tool (J-46392). Tighten the bolts on the barring device to 25 N·m (18 lb·ft). Insert the locking pin to block the device and prevent it from rotating. 6. Using J-46385, the flywheel and main pulley socket tool, remove two flywheel multi-point socket head bolts from the flywheel, 180 degrees apart. See Figure 1.
Emergency Department Visits for Chest Pain and Abdominal Pain: United States, 1999–2008 Farida A. Bhuiya, M.P.H.; Stephen R. Pitts, M.D., M.P.H., F.A.C.E.P.; and Linda F. McCaig, M.P.H., Division of Health Care Statistics Key findings Data from the National Hospital Ambulatory Medical Care Survey: 1999–2008 • The number of noninjury emergency department (ED) visits in which abdominal pain was the primary reason for the visit increased 31.8%. • The percentage of ED visits for which chest pain was the primary reason decreased 10.0%. • Use of advanced medical imaging increased strongly for ED visits related to abdominal pain (122.6%) and chest pain (367.6%). Chest and abdominal pain are the most common reasons that persons aged 15 years and over visit the emergency department (ED) (1). Because EDs provide both emergency and nonemergency care (2,3), visits for these symptoms may vary in their acuity. Advanced medical imaging is often ordered to assist in both diagnosing and ruling out serious illness associated with these symptoms (4,5). This report describes trends in visits for chest and abdominal pain in adults and the seriousness of illness and use of imaging in these visits. All data shown are for persons aged 18 and over whose visit was not injury related. Keywords: National Hospital Ambulatory Medical Care Survey • advanced medical imaging • reason for visit Are ED visits for chest or abdominal pain increasing?
Starting mid-2008, Roche introduces a new global packaging design for prescription medicines. This will meet requirements and expectations of health authorities, medical professionals and patients worldwide. The new packaging allows quick and easy identification of the medicine and dosage strength. one product colour specific dosage colour icon of pharmaceutical form dosage colour is repeated How was the design selected? Roche sought feedback from medical professionals and health authorities and reviewed possible design options with more than 700 doctors, pharmacists, nurses and patients worldwide. There was clear support for the selected new design and respondents particularly highlighted that it was easy to recognise. What are the new features? The new packaging design includes d • istinct product and dosage colours for quick identification c • olour banding visible from three sides p • lunger rods and flip-off caps in dosage colours The design is in line with recent regulatory labelling guidelines and industry best practices. There will be no changes in pack dimensions and text. How will the design be implemented? The new packs will be phased in for Roche prescription medicines between mid-2008 and 2010 (approx.). C • ellCept, Copegus, Pegasys and Xeloda will be the first medicines to feature the new packaging design (some country-specific exceptions) T • he remaining medicines will change over the coming months Packs in the old design will not be replaced and can be used until expiry. Please contact your local Roche Office for country-specific details. F. Hoffmann-La Roche Ltd 4070 Basel Switzerland www.roche.com © 2008
Zero gravity recliners gives your body a Zero Gravity Position where your legs are elevated above your heart, putting the back in a correct resting position where your spine makes an S curve and reduces all the pressure on your back. This position reduces the pressure on your spine by 15% as compared to lying horizontally. Since all our body parts are co-dependent, this zero gravity posture is beneficial to other areas as well: Lung capacity is expanded to ease breathing and boost oxygen levels in the blood, while circulation improves to minimize stress on the heart, which in turn leaves you with less muscle fatigue and a completely relaxed feeling overall. It's no wonder that Zero Gravity recliners are recommended by many physicians and health care professionals, and is the closest thing you'll find here on earth to the weightless conditions of outer space. For More Details Visit Our Website URL: http://www.backrxspinecare.com
Pensez à recycler Think recycling Publication no 2013-05-01 de la série Regards sur le monde : avis d’experts This report contains the results of a research project led by the academic outreach program of the Canadian Security Intelligence Service (CSIS) to explore the future of the Al-Qaeda phenomenon. It consists of alternative future scenarios developed during a workshop, as well as four original papers written by individual specialists at the request of CSIS. The report is not an analytical document and does not represent any formal assessment or position of CSIS or the Government of Canada. All components of the project were held under Chatham House rule; therefore, the identity of the authors and the participants is not disclosed. www.csis-scrs.gc.ca Published April 2013 Printed in Canada © Her Majesty the Queen in Right of Canada Photo credit: istockphoto.com World Watch: Expert Notes series publication No. 2013-05-01 Le présent rapport contient les conclusions d’un projet d’étude mené dans le cadre du programme de liaison recherche du Service canadien du renseignement de sécurité (SCRS) pour examiner l’avenir du phénomène al-Qaïda. Il présente des scénarios envisagés lors d’un atelier, ainsi que quatre études originales rédigées par différents spécialistes à la demande du SCRS. Le présent rapport n’est pas un document analytique et ne représente pas la position officielle du SCRS ou du gouvernement du Canada. Tout le projet s’est déroulé conformément à la règle de Chatham House; les auteurs ne sont donc pas cités et les noms des participants ne sont pas révélés. www.scrs-csis.gc.ca Publié en avril 2013 Imprimé au Canada © Sa Majesté la Reine du chef du Canada Crédit photo : istockphoto.com Ce document est imprimé avec de l’encre sans danger pour l’environement
Thank you for purchasing this Clarke Trolley Jack. Before attempting to use the unit, please read this instruction booklet thoroughly, and follow all directions carefully, paying particular attention to the safety precautions. By doing so, you will ensure the safe operation of the unit, and the safety of yourself and others around you. You can then look forward to long and reliable service from your CLARKE Trolley Jack. This CLARKE product is guaranteed against faulty manufacture for a period of 12 months from the date of purchase. Please keep your receipt which will be required as proof of purchase. This guarantee is invalid if the product is found to have been abused in any way, or not used for the purpose for which it was intended. Faulty goods should be returned to their place of purchase, No product can be returned to us without prior permission. This guarantee does not effect your statutory rights. 1. This jack is for lifting ONLY..DO NOT move a load using the jack as a dolly 2. Always inspect the jack before use. Ensure that all parts are in good condition and operating smoothly, the wheels are sound and that no cracks or distortion is apparent. If in doubt do not use. Have the parts replaced or consult your CLARKE dealer. 3. Ensure jack is on a firm solid base, and there is no possibility of it slipping when under load. 4. Ensure the load is taken by the FULL saddle and that the point of lift on the load, is of sufficient strength to support the full load adequately. 5. Always ensure that the load is stabilised or supported in such a way that it will not shift during lifting or lowering operations. 6. Always use supports to stabilise the load once lifted. NEVER work on or under a load unless it is fully and adequately supported. NEVER rely upon the jack to hold the load in position. 7. Never push a load off the jack. 8. Ensure that all personnel are well clear of a load being raised, or lowered. 9. NEVER exceed the rated load for the jack (see ‘Specifications’). 10. Do not use if an oil leak is apparent...Consult your Clarke dealer.
- RENAULT Please read the complete document before starting the installation Brand assignment SEAS add-on module is delivered NOT PROGRAMMED, therefore a brand (Renault in this case) must be set with computer and specific program SETUP TRUCK This procedure can be achieved both before and after the installation on the vehicle (if after the installation, the vehicle power batteries must be disconnected during the operations). • Connect the programming cable to the USB port of your PC • Connect the programming cable to the SEAS module by using the white 4 pins connector; during this operation the LED (Light Emission Diode) of the SEAS module will be off. • Run the program SimulaCan (select it from the list of programs installed on your pc). • Proceed as follow: Select “Start” Wait for next screen displayed (the time required can vary according to the quantity of virtual COM installed) Renault_eng.doc Pagina 1 di 5 Ver. 0.1 If the connection is successfully achieved (serial communication recognized and accepted) the program will display this page: you can now select RENAULT brand Select “Send PROG” When the programming operation is completed, the yellow LED on your SEAS module will turn on. Select “Quit” to close the program SimulaCan • Disconnect the programming cable of your SEAS module and place the specific cover on top of the white 4 pins connector. IMPORTANT: the following instructions indicate how to connect and install your SEAS module on the original AdBlue system of the truck. The number displayed and the colour of the conductors of the AdBlue system are referred to Renault Premium 450 year 2008, these details may vary according to different production lots or vehicle equipment. Please refer to the schemes/layouts supplied with the Renault technical manual to identify the CAN-Bus line of the AdBlue system, its protection fuse and the power feeding. The main working procedure of SEAS modules does not vary.
Gateway Lite BT enables music playback from a USB storage or iPod through your vehicle’s entertainment system, using the buttons of the car stereo for basic control. Once the head unit has been removed, disconnect the antenna cable (1) and then unclip the main wiring connector from the head unit (2). This will differ in all makes and manufacturers. This device also offers handsfree mobile call handling via the original buttons of the Head Unit (Radio). Connect the 12 way micro-fit (12 pin molex) to the Car side of the Gateway Lite BT module. The Dension Gateway Lite BT is available in specific versions for different vehicle types, therefore the exact operation and installation may be different in each case. Warning! Do not trap the cables, or leave them in a position where they may become trapped after refitting the head unit. Ensure the device is correctly fitted before running the cable. Then, reconnect the Dension supplied main radio connector to the rear of the head unit. Gateway Lite BT is designed to give easy to manage control, in cars where it is not possible to display text, therefore only basic control is available (track skip functions and USB folder browsing). At first please make sure that the vehicle compatibility is correct. Connect the round iPod connector and USB to the module and feed them through the dashboard to an appropriate location. With the main radio cable removed, first connect the Dension supplied cable to the original factory cable harness.
Commerzbank Aktiengesellschaft Lagebericht der Commerzbank Aktiengesellschaft Struktur und Organisation Unternehmerische Verantwortung Die Commerzbank Aktiengesellschaft ist das zweitgrößte Kredit- Die Commerzbank bekennt sich unverändert zu ihrer unternehme- institut sowie eine der führenden Privat- und Firmenkundenban- rischen Verantwortung. Dies hat sie auch 2013 unter Beweis ge- ken in Deutschland. Unseren Kunden steht eines der dichtesten stellt. Filialnetze aller deutschen Privatbanken zur Verfügung. Insge- 2013“ zeigt auf, in welchem Umfang ökologische, soziale und samt betreut die Commerzbank rund 15 Millionen Privat- sowie ethische Kriterien in den verschiedensten Einheiten der Bank ge- 1 Million Geschäfts- und Firmenkunden weltweit. Ziel der Commerz- lebt und gefördert werden. Ob Fragen der Unternehmensführung, bank ist es, ihre Position als Marktführer im Privat- und Firmen- spezifische Angebote in den Marktsegmenten, das zertifizierte kundengeschäft in Deutschland weiter zu stärken. Umweltmanagement, nachhaltige Beschaffung, die vielfältigen Die Commerzbank gliedert ihre Geschäftstätigkeit in die vier Der „Bericht zur unternehmerischen Verantwortung Leistungen für Mitarbeiter oder das gesellschaftliche Engagement Corporates – in allen Beiträgen wird klar, dass die Bank es ernst meint mit der & Markets sowie Central & Eastern Europe. In dem Abbausegment neuen Positionierung als fairer und kompetenter Partner an der Non-Core Assets (NCA) hat die Bank neben dem Staatsfinanzie- Seite ihrer Kunden. Der Bericht trägt den Titel „Verantwortung.