SEARCH

Found 5495 related files. Current in page 1

replace valve cover gasket on 2002 ford explorer

Vacuum Brake Booster Testing and Diagnosis.pdf

Vacuum Brake Booster Testing and Diagnosis Vacuum Brake Booster Testing and Diagnosis This procedure will require the use of a hand operated vacuum pump with a vacuum gauge. If you do not own one it can often be rented or borrowed from most “big box” parts stores. (Note: 18”HG is the minimum engine vacuum at idle in gear to effectively operate a vacuum booster 1) Remove vacuum hose from check valve on booster. Place hose from vacuum pump onto check valve and draw booster to 20” of vacuum. 2) Let booster sit with vacuum applied for 5 minutes. If vacuum does not stay steady at 20” it is faulty and needs to be replaced. If vacuum does hold steady at 20” proceed to step 3. 3) With 20” of vacuum in booster depress brake pedal once and release it. The booster should transfer some but not the entire vacuum in reserve. Depending on how hard the pedal is depressed it is normal to see 5-10” of vacuum depleted from reserve. The most important thing is to ensure the booster does transfer vacuum but does NOT transfer the entire vacuum in its reserve. If vacuum remains at 20” OR goes to zero the booster is bad and will need to be replaced. If vacuum transfer is within the above parameter proceed to step 4. 4) Once again draw booster down to 20” of vacuum. Go inside car and depress brake pedal and hold down for 30 seconds. You should see the gauge drop slightly and then hold steady. Vacuum should stay steady as long as you are holding the pedal down. If vacuum drops while pedal is being held down the booster is faulty and will need to be replaced.

BPI 10-06 Temporary reduction in power brake ... - Raybestos Brakes

No. BPI 10-06 Subject: Temporary reduction in power brake assist in extreme cold weather Vehicles Involved: Models: 2009 BUICK ENCLAVE 2009 CHEVROLET TRAVERSE 2009 GMC ACADIA 2009 SATURN OUTLOOK From 9J100008 From 9S100002 From 9J100016 From 9J100003 to to to to 9J190898 9S143268 9J190899 9J190888 Condition: If the brake check valves are NOT installed correctly, an increased amount of brake pedal effort will be required to obtain brake function, and the brake assist system will NOT perform as designed. Repair: Replace the first design brake booster vacuum hose check valve (1) with a second design brake booster vacuum hose check valve (2). An arrow on the second design check valve indicates the vacuum draw direction (3). 1. Remove the fuel injector sight shield (engine cover) from the engine. 4400 Prime Parkway McHenry, IL 60050  (815) 363-9000 Determine where the two brake booster vacuum hose check valves are located. Refer to callouts 1 and 2 in the illustration 2. Release the quick connect (4) from the power brake booster auxiliary pump (3). 3. Remove the protective wrap (5) from the brake booster vacuum hose to locate check valve # (1). 4400 Prime Parkway McHenry, IL 60050  (815) 363-9000 4. Remove the check valve (1) from the brake booster vacuum hose that routes to the power brake booster auxiliary pump (3). 5. Remove the check valve (2) from the brake booster hose that routes to the intake manifold vacuum port (6). Note If necessary, a small amount of denatured alcohol can be used as an assembly aid for installing the vacuum hose to the manifold vacuum port. Do not use soap. 6. Install a new check valve (1) to the brake booster hose that routes to the power brake booster auxiliary pump (3). Ensure the arrow on the check valve (1) ...

Brake Booster - Subaru Outback Forums
by moncoZ 0 Comments favorite 0 Viewed Download 0 Times

(2) Four brake booster installation nuts A: REMOVAL 1) Remove or disconnect the following parts in the engine compartment. (1) Disconnect the connector of brake fluid level gauge. (2) Remove the brake pipe from the master cylinder. (3) Remove the master cylinder installation nut. (1) CAUTION: In order to prevent the contact of the bracket and check valve, be sure to loosen the master cylinder mounting nut while holding the bracket with hand. Otherwise it may deform the bracket. (1) Check valve (2) Bracket (4) Disconnect the vacuum hose from brake booster. 2) Remove the following parts from the pedal bracket. (1) Snap pin and clevis pin Nut Clevis pin Snap pin Operating rod Brake pedal 3) Remove the brake booster while avoiding the brake pipe. NOTE: • Make sure that the booster shell and vacuum pipe are not subject to strong impacts. • Be careful not to drop the brake booster. If the booster is dropped, replace it. • Use special care when handling the operating rod. If excessive force is applied to the operating rod, the angle may change by r3°, and it may result in damage to power piston cylinder. • Be careful when placing the brake booster on floor. • Do not change the push rod length. CAUTION: • Do not disassemble the brake booster.

Chase Bays 240sx Booster Delete Brake Line ... - Chase Bays, Inc

Chase Bays 240sx Booster Delete Brake Line Relocation Kit Install Guide What is included? •(1) Stainless steel engine bay hard line •(6) Stainless braided/Teflon coated crimped brake lines •(1) -­‐3AN Bulkhead Tee fitting (Gold in color) •(1) Female -­‐3AN Tee Fitting w/ male fitting on leg (Black in color) •(2) Straight -­‐3AN Bulkheads (1) 90 degree -­‐3AN Bulkhead (4) Bulkhead nuts •(1) -­‐3AN tube nut (for rear line) •(1) -­‐3AN tube sleeve (for rear line) •(1) Wilwood Proportioning Valve with -­‐3AN male fittings •Uninstall all OEM Brake hard lines and Booster/Master Cylinder. •Install your Chase Bays Brake Booster Delete Kit. Start with drilling your engine bay hole. Install the hard line to help line up the hole correctly.

Daily Delta Connection Jet Flights to Arrive in ... - SkyWest Airlines

FOR IMMEDIATE RELEASE Daily Delta Connection Jet Flights to Arrive in Twin Falls this Summer Jet Flights Operated by SkyWest Airlines TWIN FALLS, Idaho March 26, 2014 – Flying in and out of Twin Falls is about to get an upgrade with the start of new jet service this summer. The daily Delta Connection flights, operated by SkyWest Airlines, are scheduled to begin June 5. This transition to larger, jet aircraft will continue to make flying out of Magic Valley Regional Airport simple and convenient. “SkyWest is pleased to offer jet service in Twin Falls beginning this summer,” said Mike Thompson, SkyWest Airlines vice president – Market Development. “The new jet service will continue to provide Twin Falls passengers access to destinations around the globe via Delta’s worldwide network.” The twice-daily jet service will be onboard the 50-passenger Bombardier-manufactured Canadair Regional Jet 200 (CRJ200) and will replace the current 30-passenger EMB 120 Brasilia flights. “The beginning of Delta Connection jet service here in Twin Falls is exciting news,” said Bill Carberry, Manager of Magic Valley Regional Airport. “This new aircraft, coupled with excellent connections at Salt Lake City Airport, will keep our travelers moving and the Magic Valley growing well into the future.” Each of the flights between Twin Falls and Salt Lake City has been timed to provide optimum connection opportunities in Salt Lake. From there, passengers can easily connect on hundreds of daily flights to cities from coast to coast and around the world with Delta’s extensive network. Customers may begin booking flights immediately at www.delta.com or by calling Delta reservations at 800.221.1212. Remember, the best fares are always available at www.delta.com. This press release and additional information about SkyWest Airlines can be found at www.skywest.com. About SkyWest Airlines:...

DRIVESHAFT AND UNIVERSAL JOINT SERVICE ... - worldtracker.org

M10_BIRC4058_05_SE_C10.QXD 3/30/07 Chapter 10:52 AM Page 255 10 DRIVESHAFT AND UNIVERSAL JOINT SERVICE OBJECTIVES After studying Chapter 10, the reader should be able to: 1. Perform the maintenance operations needed to keep a driveshaft operating properly. 2. Diagnose the cause of common FWD driveshaft problems. 3. Recommend the proper driveshaft repair procedure. 4.Correct RWD U-joint angularity and driveshaft balance problems. 5.Remove and replace FWD and RWD driveshafts. 6.Disassemble, inspect, and reassemble the common U-joints. 7.Make normal U-joint and CV joint repairs. 8.Complete the ASE tasks for content area D, Driveshaft and Universal/Constant-Velocity Diagnosis and Repair. KEY TERMS Antilock braking system (ABS) (p. 274) Balancing (p. 268) Grease spray (p. 258) Level protractor (p. 267) Phasing (p. 265) Plug-in connection (p. 272) Reluctor (p. 274) Runout (p. 262) 46106...

XT100-08am Driveshaft Vibration.pdf - JagRepair.com - Jaguar ...

X-TYPE DATE 05/04 Amended 09/04 XT100-08 TECHNICAL BULLETIN SERVICE Driveshaft Vibration – Diagnostic Method – Repair MODEL 2002-04 MY X-TYPE VIN C00001-E02938 Remove and destroy Bulletin XT100-08, dated 05/04. Replace with this Bulletin. Revisions are marked with a bar and in bold text. Issue: A new procedure has been developed for use after the WDS Vehicle Vibration Analyzer (VVA) has confirmed a vehicle vibration. Action: After a driveshaft vibration has been confirmed using WDS VVA, follow the workshop procedure outlined below. WORKSHOP PROCEDURE Note: There is no Labor Time Allowance to carry out road test diagnosis. Jaguar recommends a claim of 0.50 hrs. as straight time for VVA. Warning: Driveshaft bolts are one-time use only. Use new bolts for the final repair. Existing bolts may be reused throughout the diagnostic procedures. Raise vehicle on twin-post lift. Check for alignment of the green line on the rear differential flange with white paint spot on the rear of the driveshaft. If not aligned continue from step 3; if aligned continue from step 16. Remove the rear driveshaft joint to rear differential flange bolts and links where accessible. Rotate the driveshaft and remove the remaining rear driveshaft joint to rear differential flange securing bolts and links. Displace driveshaft from the rear differential flange. Remove and discard the gasket from the rear differential flange (where installed). Clean the mating faces. Install a new gasket to the rear differential flange, if previously installed. NOTE: THE INFORMATION IN TECHNICAL BULLETINS IS INTENDED FOR USE BY TRAINED, PROFESSIONAL TECHNICIANS WITH THE KNOWLEDGE, TOOLS, AND EQUIPMENT TO DO THE JOB PROPERLY AND SAFELY. IT INFORMS THESE TECHNICIANS OF CONDITIONS THAT MAY OCCUR ON SOME VEHICLES, OR PROVIDES INFORMATION THAT COULD ASSIST IN PROPER VEHICLE SERVICE. THE PROCEDURES SHOULD NOT BE PERFORMED BY “DO-ITYOURSELFERS.” DO NOT ASSUME THAT A CONDITION DESCRIBED AFFECTS YOUR CAR. CONTACT A JAGUAR RETAILER TO DETERMINE WHETHER THE BULLETIN APPLIES TO YOUR VEHICLE. Date of issue 05/04 Amended 09/04

BYS9063_Form 2359 Tube Replacement.indd - Bryan Boilers

Tube Replacement Instructions: CL/CLM & HECL/HECLM Models Bryan Steam, the originator and leader in the production of flexible tube water and steam boilers for over 90 years, is pleased to provide you with the technical and service information you need to keep your Bryan Boiler running. These instructions will give you the information you need to remove and replace tubes on a CL/CLM or HECL/HECLM Model Bryan Boiler. Here are a few points to consider when inspecting your boiler. 1. Inspect your boiler annually to find and replace bad tubes. 2. These are the two warning signs that a tube is bad: • A knocking sound in the tube bank of the boiler indicates a possibly clogged tube. • A white ash visible along the bottom of a tube or tubes indicates that the tube is getting too hot from reduced water flow. Required Tools for Tube Replacement: 1" tube puller 1" tube driver 50/50 mixture pipe dope and cutting oil 1" paint brush 3 lb. hammer 9/16" socket wrench half round file full round file piece of emery cloth a tool to bend the tube studs (or small socket/ratchet set) ...

Full System Instructions - Two Brothers Racing

Installation Instructions 1. Make sure the bike is completely cool before starting the installation. Make sure the bike is secure on a centerstand or ideally a service lift. 2. Remove rear lower cowling. 3. Remove OEM mufflers. V.A.L.E. TM 2008 Suzuki V a r i a b l e A x i s L o c k i n g E x h a u s t HAYABUSA V.A.L.E.™ Complete Exhaust System with M-2 Canister Part # 005-1930106V / 005-1930107V / 005-1930108V 8. 9. 4. The horn should also be removed for more radiator clearance. Install the TBR head pipes. (Each piece is labeled for proper postioning). From Left to Right, install head pipes 1, 2, 3, and then 4. Use the OEM gasket between the head pipes and cylinder head. Remove cowling from both the left and right sides. “M” Parts List Qty. Description 1 15” Muffler Canister 1 4-2-1 Slip-on Tube 1 4-2-1 Header Assembly 1 HARDWARE KIT 1 8x55mm Socket Head Flat Bolt (Black) 6 80mm Springs 1 8x16mm Flange Bolt 4 6x14mm Socket Head Cap Screw 1 Barrel Clamp 1 5mm Long Handle Ball End Hex Wrench 4 6mm Split Lock Washer 2 TBR Script Logo Yellow Decal 4” “1” Muffler Slip-tube Part Number Varies 005-19301S 005-19301HK 005-193-3C 005-SHF855B 005-S-80 005-FB816 005-SH814 005-27-66MSH 005-9-18610 005-WL6 015-10208-A 5. “2” “3” “R” “4” Remove radiator braces. 6. “L ” Remove O2 sensore from OEM head pipe. 10. Install the collectors to the bottom of the head pipes. The collectors are labeled “L for left and “R” for Right. ” IMPORTANT - PLEASE READ CAREFULLY We recommend that this performance part be installed by a qualified motorcycle technician. If you have any doubts as to your ability to install this performance part, please consult with your local motorcycle dealer. Read all instructions first before starting installation. Make sure the motorcycle and exhaust system are completely cool before starting the installation. Also, make sure the bike is secure on a centerstand or ideally a service lift during installation. Be sure to save all stock components for possible use later.

Suzuki Hayabusa & GSX-R 1000 Cylinder Head ... - Vance & Hines

Suzuki Hayabusa & GSX-R 1000 Cylinder Head Price Sheet Vance & Hines Motorsports has the experience and most up to date computer controlled machines for every facet of engine preparation and performance parts. Byron Hines engines and pro heads have set more records and won more races than anyone else in motorcycle drag racing. Vance & Hines Motorsports also offers comprehensive head packages for Road Racing, Motorcross and Supercross engines. Hayabusa Heads Pro Port $1,320.00 Street Port $ 625.00 Competition Valve Job & Drop Valve Guides $ 375.00 Competition Valve Job $ 375.00 Surface $ Surface $ 60.00 $1,755.00 60.00 $1,060.00 Optional Parts & Service • • • • • • • • Weld Emission Ports Cam Cut (Cam Caps) (.425 Lift & above) 99-07 Spring Kit with Titanium Retainers 08 Spring Kit with Titanium Retainers Valve Seals Stainless Steel Oversize Valves Camshafts Adjustable Cam Sprockets $ 100.00 $ 150.00 $ 365.63 $ 399.00 $ 45.00 $ 360.00 $ 698.00 $ 145.00 GSX-R 1000 Heads Pro Port $1,320.00 Street Port $ 625.00 Competition Valve Job & Drop Valve Guides $ 375.00 Competition Valve Job $ 375.00 Surface $ Surface $ 60.00 $1,755.00 60.00 $1,060.00 SF-1020 Flowbench Optional Parts & Service • • • • • • • Weld Emission Ports Bore Lifter Buckets Valve Springs Valve Seals Stainless Steel Oversize Valves Camshafts Adjustable Cam Sprockets...

« previous  123456789