Found 1058 related files. Current in page 1
Installation Instructions for CRF 150R and KX450F Steahly Flywheel Weight Warning: Improper instalation of this flywheel weight could result in engine damage or a serious crash. If you do not have the tools or the mechanical abilities take it to a professional. 1. Drain the engine oil or turn off the gas and lay the bike on its side. 2. Remove the shift lever. 3. Remove the ignition cover. Take care not to tear the gasket or have a new gasket on hand. Be carefull that you don’t lose the two dowel pins that are between the cover and the engine case. 4. Remove the flywheel nut. Use an air impact wrench or figure out a way to keep the flywheel from rotating while you remove the nut. A strap wrench or an automotive oil filter wrench may work as a holding tool or try putting the bike in high gear and holding the rear brake on. 5. Pull off the stock flywheel with the proper flywheel puller that has a crank end protection cap. Steahly part number E-63. Do not attempt removal with out the correct puller. Do not use claw type pullers. 6. Fit the flywheel weight on to the stock flywheel. Line up the two threaded holes in the weight with two holes in the stock flywheel. 7. Clean the threads of the two special bolts with contact cleaner. Put a big drop of red Loctite or other high strength thread locker on the threads of the 2 bolts. Install the two special bolts as shown in the picture and torque to 12 foot pounds. 8. Unless you plan to take the weight on and off a lot we highly recommend using a center punch and a hammer to flare out the threads at the end of the bolt (see pictures below). This will reduce the possibility of the bolt coming loose. 9. Clean up the flywheel and weight and remove any metal stuck to the magnets. 10. Install the flywheel with weight back onto the tapered crank shaft end making sure the key ways are lined up. Torque the stock nut to 42 ft- lbs.
WARNING Before playing this game, read the Xbox 360® console and accessory manuals for important safety and health information. Keep all manuals for future reference. For replacement console and accessory manuals, go to www.xbox.com/support. Important Health Warning About Playing Video Games Photosensitive seizures A very small percentage of people may experience a seizure when exposed to certain visual images, including flashing lights or patterns that may appear in video games. Even people who have no history of seizures or epilepsy may have an undiagnosed condition that can cause these “photosensitive epileptic seizures” while watching video games. These seizures may have a variety of symptoms, including lightheadedness, altered vision, eye or face twitching, jerking or shaking of arms or legs, disorientation, confusion, or momentary loss of awareness. Seizures may also cause loss of consciousness or convulsions that can lead to injury from falling down or striking nearby objects. Immediately stop playing and consult a doctor if you experience any of these symptoms. Parents should watch for or ask their children about the above symptoms— children and teenagers are more likely than adults to experience these seizures. The risk of photosensitive epileptic seizures may be reduced by taking the following precautions: Sit farther from the screen; use a smaller screen; play in a well-lit room; do not play when you are drowsy or fatigued. If you or any of your relatives have a history of seizures or epilepsy, consult a doctor before playing.
A very small percentage of people may experience a seizure when exposed to certain visual images, including flashing lights or patterns that may appear in video games. Even people who have no history of seizures or epilepsy may have an undiagnosed condition that can cause these “photosensitive epileptic seizures” while watching video games. These seizures may have a variety of symptoms, including lightheadedness, altered vision, eye or face twitching, jerking or shaking of arms or legs, disorientation, confusion, or momentary loss of awareness. Seizures may also cause loss of consciousness or convulsions that can lead to injury from falling down or striking nearby objects. Immediately stop playing and consult a doctor if you experience any of these symptoms. Parents should watch for or ask their children about the above symptoms – children and teenagers are more likely than adults to experience these seizures. The risk of photosensitive epileptic seizures may be reduced by taking the following precautions: Sit farther from the screen; use a smaller screen; play in a well-lit room; do not play when you are drowsy or fatigued. If you or any of your relatives have a history of seizures or epilepsy, consult a doctor before playing.
According to t he P aperwork R eduction Act o f 1995, an ag ency ma y not cond uct or sponsor, an d a p erson i s not r equired to r espond to , a c ollection of information unless it displays a valid OMB control number. The valid OMB control numbers for this information collection are 0579-0036 and 0579-0333. The ti me r equired to complete t his i nformation col lection i s esti mated t o av erage .25 h ours per r esponse, i ncluding the ti me for rev iewing in structions, searching existing data sources, gathering and maintaining the data needed, and completing and reviewing the collection of information. UNITED STATES DEPARTMENT OF AGRICULTURE ANIMAL AND PLANT HEALTH INSPECTION SERVICE UNITED STATES INTERSTATE AND INTERNATIONAL CERTIFICATE OF HEALTH EXAMINATION FOR SMALL ANIMALS WARNING: Anyone who makes a false, fictitious, or fraudulent statement on this document, or uses such document knowing it to be false, fictitious, or fraudulent may be subject to a fine of not more than $10,000 or imprisonment of not more than 5 years or both (18 U.S.C. 1001).
Ensure the jack is in sound condition and good working order. Take action for immediate repair or replacement of damaged parts. Use genuine parts only. The use of improper parts may be dangerous and will invalidate the warranty. Locate the jack in a suitable, well lit working area. Keep working area clean and tidy and free from unrelated materials. Use jack on level and solid ground, preferably concrete. Avoid tarmacadam as jack may sink in. Place wedges under wheels of vehicle, but ensure the jack wheels are free to move and that there are no obstructions. Ensure the vehicle handbrake is engaged, engine is switched off and transmission is in gear (or “PARK” if automatic). Ensure minimum distance of 0.5m between vehicle and static objects such as doors, walls, etc., to allow for vehicle tilting. Ensure there are no passengers in the vehicle and that all non-essential persons keep a safe distance whilst the jack is in use. Place jack under lifting points recommended by vehicle manufacturer (see vehicle hand book). Ensure lifting point is stable and centred on saddle. WARNING! When lifting at the jack's maximum rating (2tonne) or close to it, it is recommended that the effort of raising the load shall be reduced by the use of assistance during this operation. ANGER: Use the jack for lifting only, NOT for supporting the lifted load.
Hazard warning: Incorrect installation or repair of Webasto heating systems may cause a fire or result in the emission of carbon monoxide, which can be fatal. Serious or fatal injuries can be caused as a result. Specialist company training, technical documentation, specialized tools and equipment are required to install and repair Webasto heating and cooling systems. NEVER attempt to install or repair Webasto heating or cooling systems if you have not successfully completed the company training and thereby acquired the required technical skills, or if you do not have access to the required technical documentation, tools and equipment needed to carry out correct installation and repairs. ALWAYS follow all Webasto installation and repair instructions and observe all warnings. Webasto does not accept any liability for defects and damage that are attributable to installation by untrained staff.
Gateway Lite BT enables music playback from a USB storage or iPod through your vehicle’s entertainment system, using the buttons of the car stereo for basic control. Once the head unit has been removed, disconnect the antenna cable (1) and then unclip the main wiring connector from the head unit (2). This will differ in all makes and manufacturers. This device also offers handsfree mobile call handling via the original buttons of the Head Unit (Radio). Connect the 12 way micro-fit (12 pin molex) to the Car side of the Gateway Lite BT module. The Dension Gateway Lite BT is available in specific versions for different vehicle types, therefore the exact operation and installation may be different in each case. Warning! Do not trap the cables, or leave them in a position where they may become trapped after refitting the head unit. Ensure the device is correctly fitted before running the cable. Then, reconnect the Dension supplied main radio connector to the rear of the head unit. Gateway Lite BT is designed to give easy to manage control, in cars where it is not possible to display text, therefore only basic control is available (track skip functions and USB folder browsing). At first please make sure that the vehicle compatibility is correct. Connect the round iPod connector and USB to the module and feed them through the dashboard to an appropriate location. With the main radio cable removed, first connect the Dension supplied cable to the original factory cable harness.
iPod Nano 7th Gen - Disassemble Guide • TTT-9007 Small Phillips Screwdriver • TTT-9010 Plastic Opening Tools • TTT-9013 Spudger • Heat Gun / Blow Dryer The repair of the iPod Nano 7th Gen., can be both simple and inexpensive if you follow the steps of this disassemble guide. To assist you in completing the repair, the steps we have provided will help you quickly, and safely, replace a broken display, along with other internal components that may have become damaged. You can find a full archive of fixez.com disassemble guides and videos, for numerous makes and models of phones and tablets, by visiting http://www.fixez.com. http://www.fixez.com/ Page 1 of 8 iPod Nano 7th Gen–Disassemble Guide Step 1 – Display Assembly • **Warning** We are showing the first two steps in reverse order. The Bluetooth antenna, adhered to the back of the iPod Nano’s bottom cover, is very easy to damage. • When you perform the next step, please be aware this antenna is there. Proceed with caution so that no damage is done to this piece.
The iPod interface can be used to connect an iPod to your in-car infotainment system and allows you to play audio files directly over the infotainment system. The iPod interface is located in your car's glove box. It is compatible with 3rd generation or higher iPod1) devices (made from about 2003 onwards), with the exception of the iPod Shuffle and the iPhone. The iPod is controlled using the CD function of the infotainment system (sound system or navigation system). The infotainment system allocates the playlists on the iPod first in numerical order and then in alphabetical order, as follows: • Chorus / concert sound system, Navigation System BNS 5.0: allocation as CD 1 to CD 5 • Symphony sound system: allocation as CD 7 to CD 11 The easiest way to use playlists on the car's entertainment system is to create five playlists on the iPod (e.g. 1 to 5). All the tracks on the iPod will be played as follows even if they are stored in different playlists: • Chorus / concert sound system, Navigation System BNS 5.0: via CD 6 • Symphony sound system: via CD 12 Information stored on the iPod, such as artist, track, album and genre, or the name of a playlist, does not appear on the infotainment system display. 1) iPod is a registered trademark of Apple Computer Inc. WARNING • Today's driving conditions require your full attention. As the driver, you have full responsibility for the safety of the vehicle and other road users. For this reason, operate the iPod only when the traffic conditions allow you to do so safely and when you can maintain proper control of your vehicle - risk of accident! • The volume of the audio sources (radio, CD player, etc.) should only be set at a level which enables you to hear distant police and emergency vehicles clearly - failure to do so could result in an accident. Caution Very high or very low temperatures (a common occurrence in a car's interior) can cause damage to the iPod and/or impair its performance. • Please do not leave your iPod in the vehicle in case of extreme temperatures. Note Please refer to the iPod operating instructions for important information on how to use your iPod.
February 2005 Supersedes J3311-DSD May 1994 Contact Information: Dana Corporation Heavy Vehicle Technologies and Systems Service P.O. Box 321 Toledo, OH 43697-0321 1-800-SAY-DANA (729-3262) Dana Corporation Heavy Vehicle Technologies and Systems Service – Canada 5095 South Service Road Beamsville, Ontario, Canada L0R 1B0 Tech Service: 1-905-563-4991 www.dana.com www2.dana.com/expert J3311-1-HVTSS 2/05 Printed in U.S.A. © Dana Corporation 2005 All rights reserved. Dana Corporation Heavy Vehicle Technologies and Systems Service – International 419-861-6325 Driveshaft Installation Safety Precautions General Safety Information WARNING: GUARDING AUXILIARY DRIVESHAFTS To prevent injury to yourself and /or damage to the equipment: • Read carefully all owners manuals, service manuals, and/or other instructions. • Always follow proper procedures and use proper tools and safety equipment. • Be sure to receive proper training. • Never work alone while under a vehicle or while repairing or maintaining equipment. • Always use proper components in applications for which they are approved. • Be sure to assemble components properly. • Never use worn-out or damaged components. • Always block any raised or moving device that may injure a person working on or under a vehicle. • Never operate the controls of the power take-off or other driven equipment from any position that could result in getting caught in the moving machinery. We strongly recommend that a power take-off and a directly mounted pump be used to eliminate the auxiliary driveshaft whenever possible. If an auxiliary driveshaft is used and remains exposed after installation, it is the responsibility of the vehicle designer and PTO installer to install a guard. WARNING: USING SET SCREWS.