Found 2854 related files. Current in page 1
Installation Instructions BEFORE YOU BEGIN Over the Range Microwave Oven Read these instructions completely and carefully. • IMPORTANT – Save these instructions for • Proper installation is the responsibility of the installer. local inspector's use. • • Product failure due to improper installation is not covered under the Warranty. • Please read all instructions thoroughly before installing the Over the Range Microwave Oven. Two people are recommended to install this product. • If a new electrical outlet is required, its installation should be completed by a qualified electrician before the Microwave Oven is installed. See 3 ELECTRICAL GROUNDING INSTRUCTIONS on page 2. IMPORTANT – Observe all governing codes and coordinates. • Note to Installer – Be sure to leave these • Note to Consumer – Keep these instruc- instructions with the Consumer. tions for future reference. • Skill Level – Installation of this appliance requires basic mechanical and electrical skills. UNPACKING AND EXAMINING YOUR OVEN Open the bottom of the carton, bend the carton flaps back and tilt the oven over to rest on plastic foam pad. Lift carton off oven and remove all packing materials, WALL and TOP CABINET TEMPLATE, Turntable, and Turntable Support. SAVE THE CARTON AS IT MAY MAKE INSTALLATION EASIER. 1. Remove the feature sticker from the outside of the door, if there is one. 2. DO NOT REMOVE THE WAVEGUIDE COVER, which is located on the right side wall of the oven cavity. Check to see that there is a Wall TEMPLATE and Top CABINET Template. Read enclosures and SAVE the Operation Manual. Oven Cavity Hinges Door seals and Safety door sealing surfaces latches Check the oven for any damage, such as misaligned or bent door, damaged door seals and sealing surfaces, broken or loose door hinges and latches and dents inside the cavity or on the door. If there is any damage, do not operate the oven and contact your dealer or ELECTROLUX AUTHORIZED SERVICER. See Installation Instructions for more details. NEED HELP? For customers in the United States, call: 1-800-944-9044 For customers in Canada, call: 1-800-213-9397 (English) 1-800-668-4606 ext.8199 (French) READ CAREFULLY. KEEP THESE INSTRUCTIONS.
Welcome & Congratulations Congratulations on your purchase of a new range! At Electrolux Home Products, we are very proud of our product and are completely committed to providing you with the best service possible. Your satisfaction is our number one priority. We know you’ll enjoy your new range and Thank You for choosing our product. We hope you consider us for future purchases. PLEASE CAREFULLY READ AND SAVE THESE INSTRUCTIONS This Use & Care Manual provides specific operating instructions for your model. Use your appliance only as instructed in this manual. These instructions are not meant to cover every possible condition or situation that may occur. Common sense & caution must be practiced when installing, operating & maintaining any appliance. Please record your model and serial numbers below for future reference. Model Number: Serial Number: Serial plate is located behind the broil or storage drawer on the lower right side of the appliance frame. Purchase Date: This Use & Care Manual contains general operating instructions for your appliance and feature information for several models. Your range may not have all the described features. The graphics shown are representative. The graphics on your range may not look exactly like those shown. Product Registration Be sure to register your product. The self-addressed PRODUCT REGISTRATION CARD should be filled in completely, signed and returned to Electrolux Home Products.
PLEASE READ THESE INSTRUCTIONS BEFORE INSTALLING. 1. You should always disconnect the battery, negative lead first, before working on the ignition system. When you are done reconnect the battery installing the positive lead first. 2. The drive gear installed on this distributor is melonized and therefore compatible with flat tappet or hydraulic roller camshafts. If it is to be installed with a mechanical roller camshaft, a bronze or other such compatible gear for the 0.500” shaft will need to be purchased and installed. HOW TO INSTALL THE DISTRIBUTOR 1. If the distributor to be replaced has not already been removed from the engine, remove its cap. Do not remove the spark plug wires at this time. 2. Crank the engine slowly until the rotor blade aims at a fixed point on the engine or firewall. Note this point for future reference. 3. Unplug all external connectors coming from the distributor. 4. Now put the existing cap back on and note and mark which spark plug wire the rotor (blade) is pointing at. Then number the wires according to cylinder and remove the wires. If in doubt you can leave the wires connected to the old cap and transfer them to the new cap and distributor later in the process (see point # 9).
Important: Read these instructions before attempting the installation. Parts Included: 1 - Pro-Billet Distributor 1 - Rotor, PN 8467 1 - Distributor Cap, PN 8433 1 - Wire Retainer 2 - 1.5" Self Tapping Screws 2 - 10-32 x 3/4" Socket Head Screws 1 - Advance Kit 1 - 3-Pin Harness 1 - Gasket 1 - Tube of Gear Lubricant 2 - O-Rings 1 - Vacuum Advance Lockout Kit 1 - Coil Wire 1 - Blaster SS Coil, PN 8207 WARNING: Before installing the MSD Ready to Run Distributor, disconnect the battery cables. When disconnecting the battery cables, always remove the Negative (-) cable first and install it last. Note: The terminals of this Distributor Cap require spark plug style terminals. You may need to change the terminals and boots of your wires. MSD offers two kits, PN 8849 or PN 8848 that are supplied with nine boots and terminals.
WESTERN PRODUCTS, P.O. BOX 245038, MILWAUKEE, WI 53224-9538 Lit. No. 64127 October 31, 2003 CHEVY/GMC 1500/2500/3500 4x4 1999 & LATER VEHICLE SPECIFIC ELECTRICAL INSTALLATION INSTRUCTIONS Model No. 3515 & 3525 and Model No. 3519 & 3529 Straight Blade (Models 3515, 3525, 3519, & 3529) 2003 & Later: Harness Kit No. 64077 (HB-3 & HB-4 QUAD Lights) Headlamp Kit 12-Pin (White) No. 64078 1999-2002: Harness Kit No. 63392 (HB-3 & HB-4 QUAD Lights) Headlamp Kit 9-Pin No. 61540-1 MVP® Blade (Models 3525 & 3529) 2003 & Later: Harness Kit No. 64085 (HB-3 & HB-4 QUAD Lights) Headlamp Kit 12-Pin (White) No. 64078 1999-2002: Plug-In Harness 63394 (HB-3 & HB-4 QUAD Lights) Headlamp Kit 66640-1 MVP 12-Pin CAUTION Read this document before installing the snowplow. CAUTION See your WESTERN outlet for application recommendations. The Selection List has specific vehicle and snowplow requirements. ®
Ecosmob provides professional WebRTC solution development & customization services. Read/Download this doc for more details.
INSTRUCTION MANUAL ANGLE GRINDER MODEL: D28108-XE, D28127-XE, D28128-XE, D28154-XE SAFETY INSTRUCTIONS When using power tools, always observe the safety regulations applicable in your country to reduce the risk of fire, electric shock and personal injury. Read the following safety instructions before attempting to operate this product. Keep these instructions in a safe place. General 1. Keep work area clean. Cluttered areas and benches can cause accidents. 2. Consider work area environment. Do not expose power tools to high humidity or rain. Keep work area well lit. Do not use power tools in the presence of flammable liquids or gases. 3. Guard against electric shock. Prevent body contact with earthed surfaces (e.g. pipes, radiators, cookers and refrigerators). 4. Keep children away. Do not let children come into contact with the tool or extension cord. Keep all people away from the work area. 5. Extension cords for outdoor use. When the tool is used outdoors, always use extension cords intended for outdoor use and marked accordingly. 6. Store idle tools. When not in use, power tools must be stored in a dry place and locked up securely, out of the reach of children. 7. Dress properly. Do not wear loose clothing or jewellery. They can be caught in moving parts. Preferably wear rubber gloves and non-slip footwear when working outdoors. Wear protective hair covering to keep long hair out of the way. 8. Wear safety goggles. Also use a face or dust mask in case the operations produce dust or flying particles. 9. Be aware of maximum sound pressure. Take appropriate measures for the protection of hearing if the sound pressure of 85dB(A) is exceeded. 10. Secure workpiece. Use clamps or a vice to hold the workpiece. It is safer and it frees both hands to operate the tool. 11. Do not overreach. Keep proper footing and balance at all times. 12. Avoid unintentional starting. Do not carry the plugged-in tool with a finger on the switch. Be sure that the switch is released when plugging in. 13. Stay alert. Watch what you are doing. Use common sense. Do not operate the tool when you are tired.
INSTALLATION AND OWNER’S MANUAL Small Fireplace Insert (38” Wide) 98501001 Medium Fireplace Insert (40” Wide) 98501002 Large Fireplace Insert (42” Wide) 98501003 Read these instructions completely before beginning installation. Failure to follow them could cause a heater malfunction and result in serious injury and/or property damage. WARNING: All electric heaters have hot or sparking parts inside. Do not use it in areas where gasoline, paint or flammable liquids are stored. WARNING: This heater is tested and listed for use only with the optional accessories listed in these instructions. Use of optional accessories not specifically tested for this heater could void the heater warranty and/or result in a safety hazard. 1 Keep this manual for future reference. SAFETY INFORMATION Due to high temperatures, the insert should be located out of traffic and away from furniture and draperies. Do not place clothing or other flammable material on or near the insert. Never place any objects on the insert. The insert can become very hot when running. Keep children and adults away from hot surfaces to avoid burns or clothing ignition. The insert will remain hot for a time after shutdown. Allow surfaces to cool before touching.