Found 2232 related files. Current in page 1
Interference Between Clutch Damper and Flywheel Bolts On 2003-2006 Caterpillar 3406E C-15 & C-16 Diesel Engines The AERA Technical Committee offers the following information regarding possible interference between the clutch damper and flywheel bolts on 2003-2006 Caterpillar 3406E, C-15 and C-16 diesel engines. Engines built or serviced with the VCT plus clutch damper, introduced in April 2003, have the possibility of the clutch damper interfering with the flywheel mounting bolts. This applies to the following clutch part numbers: 108009-32Y, 108925-20, 108925-25, 108926-20Y, 108926-25Y, 109701-20, 109701-25, 109705-20Y, 109705-25Y & 109706-32Y. Correction/Action: Any repair that has required the transmission to be removed from the truck, and the engine serial number is 5EK1 and up, 6TS1 and up, 1LW1 and up, 2WS1 and up, 6NZ1-92122, 7CZ1-04382, MBN1-21447, BXS1-00984, 5DS1 and up, or 1MM1 and up, requires checking the flywheel bolt washers. You must verify the 5mm washer has been replaced with the 3mm washer, Caterpillar Part Number 8D-5054. Failure to replace the washers could result in damper rivet interference. Torque the bolts to 270 Nm +/- 40 Nm (200 ft/lb +/- 30 ft/lb). It is also suggested that paint may be applied to bolt heads to show verification and completion identification.
Installation Instructions for CRF 150R and KX450F Steahly Flywheel Weight Warning: Improper instalation of this flywheel weight could result in engine damage or a serious crash. If you do not have the tools or the mechanical abilities take it to a professional. 1. Drain the engine oil or turn off the gas and lay the bike on its side. 2. Remove the shift lever. 3. Remove the ignition cover. Take care not to tear the gasket or have a new gasket on hand. Be carefull that you don’t lose the two dowel pins that are between the cover and the engine case. 4. Remove the flywheel nut. Use an air impact wrench or figure out a way to keep the flywheel from rotating while you remove the nut. A strap wrench or an automotive oil filter wrench may work as a holding tool or try putting the bike in high gear and holding the rear brake on. 5. Pull off the stock flywheel with the proper flywheel puller that has a crank end protection cap. Steahly part number E-63. Do not attempt removal with out the correct puller. Do not use claw type pullers. 6. Fit the flywheel weight on to the stock flywheel. Line up the two threaded holes in the weight with two holes in the stock flywheel. 7. Clean the threads of the two special bolts with contact cleaner. Put a big drop of red Loctite or other high strength thread locker on the threads of the 2 bolts. Install the two special bolts as shown in the picture and torque to 12 foot pounds. 8. Unless you plan to take the weight on and off a lot we highly recommend using a center punch and a hammer to flare out the threads at the end of the bolt (see pictures below). This will reduce the possibility of the bolt coming loose. 9. Clean up the flywheel and weight and remove any metal stuck to the magnets. 10. Install the flywheel with weight back onto the tapered crank shaft end making sure the key ways are lined up. Torque the stock nut to 42 ft- lbs.
Additional service information is available in the Detroit Diesel Series 60 Service Manual, 6SE483. The next revision to this manual will include the revised information. As a convenience to holders of the Series 60 Service Manual, information in service manual format is attached. The page(s) may be inserted into the manual. NOTE: Manual insert pages are numbered for insertion into the current Series 60 Service Manual dated January 2004. Service manuals are available from authorized Detroit Diesel distributors. If this bulletin was obtained from the Internet, service manual page(s) are available by returning to the screen “SIB Index”, selecting attachment pages, and printing the page(s). Detroit Diesel®, DDC®, Series 60® and the spinning arrows design are registered trademarks of Detroit Diesel Corporation. © Copyright 2004 Detroit Diesel Corporation. All rights reserved. Printed in U.S.A.
Please check the part-number(s) for your application against the part-number(s) listed on the instruction sheet. DO NOT USE ANY WASHERS with ARP Flywheel Bolts. They are designed to be installed without them. Note: ARP will NOT be responsible for any failures resulting from using a washer with this kit. Make sure there is an adequate chamfer around the bolt holes on the flywheel to clear the radius under the head of the bolt. Lubricate the threads of the bolt with LOCTITE 242 and the under head of the bolt with ARP ULTRATORQUE FASTENER ASSEMBLY LUBRICANT. Then install the flywheel onto the crankshaft and tighten the bolts hand tight. Using an alternating or criss cross pattern, torque the bolts to 95 ft lbs using the specified lubricants in Step 4. If you have any questions or need additional information please contact us at (805) 339-2200 or by FAX at (805) 650-0742 Flywheel Bolt without Washer- Installation
Setting up Charging the rechargeable battery pack Setting up the rechargeable battery pack 1 Press the tab on the top of the controller’s battery compartment cover, then and pull down to detach the original battery from the controller. Charge your battery pack before its first use and whenever it is drained. 1 Insert the charging plug into the charge port on the front of your wireless controller. 2 Connect the USB plug to any USB port of your Xbox 360. 3 Turn on your console. The charge indicator on the front of the plug glows red as the battery pack charges. When the light glows green, the battery pack is fully charged. Rechargeable battery safety Incorrect battery use may result in battery leakage, overheating, or explosion. When using batteries, make sure that you follow these instructions: • Keep batteries out of reach of children. • Do not heat, open, puncture, mutilate, or dispose of batteries in fire. • If a battery leaks, remove the battery, taking care to keep the leaked fluid from touching your skin or clothes. If fluid from the battery comes into contact with skin or clothes, flush skin with water or remove the clothing immediately. Before inserting a new battery, thoroughly clean the controller with a damp paper towel. • Do not allow metal objects to touch the battery terminals, because they can become hot and cause burns. For example, do not carry the battery in a pocket with keys or coins. • Remove the battery when the product will not be used for an extended period of time.
Mumbai monsoon can get menacing at times. The island city takes its original shape in every monsoon when rain water gets difficult to drain out, caused by raised levels of sea around the city.
The following procedures are to be followed for scoring student answer papers for the Regents Examination in Algebra 2/Trigonometry. More detailed information about scoring is provided in the publication Information Booklet for Scoring the Regents Examinations in Mathematics. Do not attempt to correct the student’s work by making insertions or changes of any kind. In scoring the open-ended questions, use check marks to indicate student errors. If the student’s responses for the multiple-choice questions are being hand scored prior to being scanned, the scorer must be careful not to make any stray marks on the answer sheet that might later interfere with the accuracy of the scanning. Unless otherwise specified, mathematically correct variations in the answers will be allowed. Units need not be given when the wording of the questions allows such omissions. Each student’s answer paper is to be scored by a minimum of three mathematics teachers. No one teacher is to score more than approximately one-third of the open-ended questions on a student’s paper. On the student’s separate answer sheet, for each question, record the number of credits earned and the teacher’s assigned rater/scorer letter. Schools are not permitted to rescore any of the open-ended questions on this exam after each question has been rated once, regardless of the final exam score. Schools are required to ensure that the raw scores have been added correctly and that the resulting scale score has been determined accurately. Raters should record the student’s scores for all questions and the total raw score on the student’s separate answer sheet. Then the student’s total raw score should be converted to a scale score by using the conversion chart that will be posted on the Department’s web site at: http://www.p12.nysed.gov/apda/ on Tuesday, June 19, 2012.
To determine the student’s final examination score, find the student’s total test raw score in the column labeled “Raw Score” and then locate the scale score that corresponds to that raw score. The scale score is the student’s final examination score. Enter this score in the space labeled “Scale Score” on the student’s answer sheet. Schools are not permitted to rescore any of the open-ended questions on this exam after each question has been rated once, regardless of the final exam score. Schools are required to ensure that the raw scores have been added correctly and that the resulting scale score has been determined accurately. Because scale scores corresponding to raw scores in the conversion chart change from one administration to another, it is crucial that for each administration the conversion chart provided for that administration be used to determine the student’s final score. The chart above is usable only for this administration of the Regents Examination in Algebra 2/Trigonometry. Algebra 2/Trigonometry Conversion Chart - June '13
Set up - Create Account, Install Software, and Sign-In to App 1. From a computer or Mac, visit the library's website at http://www.fspl.org. Click the digital library graphic on the right side of the website. Then click the OneClickdigital graphic or link. 2. The OneClickdigital website will come up on the screen. Click Create New Account. 3. You will need to fill in the following personal information: first name, last name, zip code, email address, username, password, and operating system. 4. Then download the OneClickdigital Media Manager software. Follow the prompts in order to install the software. 5. It will prompt you to restart the computer or Mac before using the software. 6. Sign into the software with your username and password. See step 1 on back page Searching, Checking Out, and Transferring an Audiobook Revised 08-12 1. Click Browse Website. The OneClickdigital website will open in the Internet Browser. 2. Click Login at top right of the screen. Enter your username and password. 3. Search or browse for an audiobook. 4. Click the title you want to check out. On the right side of the screen you can select the number of days you want to have the audiobook. Then click Checkout Now! (See picture to the right.) 5. You will be prompted to either Open or Save the files. Click Open. 6. The title will show up in the OneClickdigital Media Manager. Click the Download/Transfer button and the audio files will start downloading. 7. Plug the MP3 player or iPod into the computer or Mac. 8. Click transfer in the OneClickdigital Media Manger. Follow the prompts to transfer the audio files to your MP3 Player or iPod. (See pictures below.) Please Note: If you are using an iPod you will need to change the iTunes settings to "Manually Manage Music..." in the "Summary" screen of your device. Then you can directly transfer the audio files from the Media Manger to the iPod. Happy Listening!