SEARCH

Found 1475 related files. Current in page 1

isuzu npr brake bleeding

Installation Instructions - Gibson Exhaust Systems

When installing this exhaust system make sure to use proper safety precautions. Use jack stands when working under the vehicle, set parking brake, block tires and use safety glasses and gloves. Allow exhaust to cool before attempting installation. Severe injury or burns could occur if safety measures are not taken. SUGGESTED TOOLS: 1/2”, 9/16” 15mm wrenches & sockets, WD-40, hacksaw, jack stands. 1. Disconnect the negative battery cable before removal of OEM exhaust. This will allow the computer to reset and recognize the new exhaust. Lay out the exhaust on the floor so it looks like the drawing and compare parts with manual. 2. To remove the stock exhaust, remove it from the clamp in front of the muffler. Disengage the welded hangers using WD40 from the OEM rubber grommets. Do not damage or remove the rubber grommets as you will reuse them to mount your new system. • 09-12 models cut tailpipe before rear axle for removal. • 2013 5.7L Models un bolt your tailpipes before and after rear axle 3. Install Head Pipe #A onto your factory pipe. Insert welded hanger into factory rubber grommet. Use Clamp # G to secure. Do not tighten. 4. Install muffler #B onto head pipe #A 1½”-2”. Use a jack stand to support the muffler. Use clamp #G to secure the muffler to the headpipe. DO NOT TIGHTEN. 5. Non Factory Dual Exhaust. Install rubber grommet hanger # I onto the factory hanger at the rear of frame on Driver Side. 6. Remove spare tire to install tailpipes (Reference vehicle manual for removal of spare tire). Now install Driver side tailpipe #D into the muffler 1½-2”. Use clamp #H to secure tailpipe to muffler. DO NOT TIGHTEN. Insert welded hangers into rubber grommets. 7. Install Passenger side tailpipe #C into the muffler 1½-2”. Use clamp #H to secure tailpipe to muffler. DO NOT TIGHTEN. Insert welded hangers into rubber grommets.

RAM 1500 Special Service Vehicle Overview, Maintenance, and Up ...

Radiator Coolant Powertrain Control Module (PCM) A/C Service Ports Antilock Brake System Up- itter PDC Battery Totally Integrated Power Module (TIPM) INTERIOR COMPONENTS Integrated Trailer Brake Module (ITBM) Instrument Cluster Jack Storage Data Link Connector (DLC) Headliner Hands-free Module Police Dome Light Restraints EXTERIOR FEATURES Heated/Fold Away Mirror Reinforced Door Hinge RAMBox Option TOWING CAPACITY AND PAYLOAD Four-way/Seven-way Electrical Connector Locating Labels and Placards Vehicle Information Plus Vehicle Identi ication Number Vehicle Certi ication Label Vehicle Emissions Certi ication Label Tire and Loading Information Label Secondary Load Label

Four Tips to Fix Car Brake Lights
by hannaozer 0 Comments favorite 10 Viewed Download 0 Times

motoraty.com is a premium destination in the Middle East where we make car buying so easy. We at motoraty.com have engineered the way online car shopper can navigate, search, and find what they are looking for. motoraty.com offers credible and easy to understand information from consumers and car experts to help car buyers formulate opinions on what to buy, where to buy and how much to pay for a new or used car. With comprehensive pricing information, dealer reviews, car comparison tools, financial tools, and a rich multimedia section that includes photo and video galleries, and unbiased editorial content. In addition, motoraty.com offers the latest car news locally and globally. With a detailed car section and comprehensive information, motoraty.com put car buyers behind the wheel, and in control. Motoraty.com was launched in June 2013, and it is available both in English and Arabic languages. Founded by Johny Giacaman who has extensive experience in digital media.

LM - Range Rover Maintenance Check Sheets ... - Niello.com

VEHICLE EXTERIOR Lubricate top edge door seals Check tire pressures condition and tread depth 3. ENGINE COMPARTMENT Check battery condition, fill electrolyte, clean terminals Check and top up: brake, PAS and windshield washer fluid Check engine coolant level and freeze protection level Inspect drive belt(s) Replace engine oil and replace filter Replace pollen filter Replace air-cleaner elements - Supercharged Replace air-cleaner elements - Naturally Aspirated Replace brake fluid Replace Supercharger drive belt (if fitted) Replace spark plugs Replace accessory drive belt Replace engine coolant 4. Every 3 years Every 105,000 mi / 168,000 km Every 105,000 mi / 168,000 km Every 150,000 mi / 240,000 km Every 10 years UNDER VEHICLE Check for fluid leaks Check adjustment of electric park brake Check condition / operation of suspension and steering components, boots, and drive axles Check brake, fuel lines, PAS hoses and unions for correct routing and damage Remove road wheels; lubricate wheel centers Inspect for brake pad wear, caliper leaks and disc condition Install road wheels to opposite side of the vehicle – except uni-directional tires which install on same side Replace transfer case fluid Replace locking differential fluid Replace front and non-locking rear differential fluid Replace fuel filter Replace automatic transmission fluid and filter 5. Every 5 years / 75,000 mi / 120,000 km Every 5 years / 75,000 mi / 120,000 km Every 10 years Every 10 years / 150,000 mi / 240,000 km Every 10 years / 150,000 mi / 240,000 km REMEDIAL WORK / SERVICE CAMPAIGN NEEDED Check for open Service Campaigns / Recalls If fault lamps illuminated use IDS to find the faults and report 6. ROAD TEST Select LOW range; move vehicle 60 ft (18 m); select HIGH range Road test vehicle Record performance of Service in vehicle's Passport to Service Labor cost not included in scheduled time NOTIFICATION OF SERVICE REQUIREMENTS:...

A C C ES SORIES
by Sukmawati 0 Comments favorite 6 Viewed Download 0 Times

accessories LOWER BODY GRAPHIC Mudguards Rear LIP Spoiler – High Profile Rear LIP Spoiler – LOW Profile Paint Protection Film REAR BUMPER APPLIQUé CARBON FIBER B-PILLAR APPLIQUÉ Door Sill Enhancements Illuminated Door Sills interior light kit Carpet Floor Mats All-Weather Floor Mats 2014 tC accessories TRD Shift Knob (A/T) TRD Quickshifter TRD High Performance Big Brake Kit TRD 19-in. Alloy Wheels TRD OIL CAP TRD OIL FILTER TRD LOWERING SPRINGS TRD FRONT STRUT TIE BRACE TRD SWAY BAR KIT TRD PERFORMANCE EXHAUST TRD PERFORMANCE AIR FILTER CARGO COVER Carpet Cargo Mat Cargo Net – SPIDER CARGO TRAY CARGO TOTE BeSpoke® Premium Audio Scion STANDARD DISPLAY AUDIO SCION SECURITY SYSTEM REMOTE ENGINE STARTER Alloy Wheel Locks AUTO-DIMMING rearview MIRROR Shift KnobS > > The car you drive is a small reflection of yourself. Make it truly yours with Genuine Scion Accessories that both protect and enhance your tC. Every accessory has been designed, engineered and manufactured with the highest quality that you’ve come to expect from Scion, so that you may enjoy your own unique tC for years to come. Lower Body Graphic Run this lower body graphic down the side of the car, and you’ll add a visual exclamation point to the sleek lines of your tC. • Features dual stripes and integrates Scion logo cut out • Dark graphite color ensures the graphic stands out on most vehicle colors • Made from tough, UV-resistant polyurethane that won’t yellow, fade or peel > > Mudguards Mudguards help keep the lower side panels of your machine pristine and clean while protecting against chipping. • Precise fit to match vehicle body panels and structure • Meets factory ground clearance entry and departure angles

520 CRF 150R and 625 KX 450F 06-08 Flywheel ... - Steahly Offroad

Installation Instructions for CRF 150R and KX450F Steahly Flywheel Weight Warning: Improper instalation of this flywheel weight could result in engine damage or a serious crash. If you do not have the tools or the mechanical abilities take it to a professional. 1. Drain the engine oil or turn off the gas and lay the bike on its side. 2. Remove the shift lever. 3. Remove the ignition cover. Take care not to tear the gasket or have a new gasket on hand. Be carefull that you don’t lose the two dowel pins that are between the cover and the engine case. 4. Remove the flywheel nut. Use an air impact wrench or figure out a way to keep the flywheel from rotating while you remove the nut. A strap wrench or an automotive oil filter wrench may work as a holding tool or try putting the bike in high gear and holding the rear brake on. 5. Pull off the stock flywheel with the proper flywheel puller that has a crank end protection cap. Steahly part number E-63. Do not attempt removal with out the correct puller. Do not use claw type pullers. 6. Fit the flywheel weight on to the stock flywheel. Line up the two threaded holes in the weight with two holes in the stock flywheel. 7. Clean the threads of the two special bolts with contact cleaner. Put a big drop of red Loctite or other high strength thread locker on the threads of the 2 bolts. Install the two special bolts as shown in the picture and torque to 12 foot pounds. 8. Unless you plan to take the weight on and off a lot we highly recommend using a center punch and a hammer to flare out the threads at the end of the bolt (see pictures below). This will reduce the possibility of the bolt coming loose. 9. Clean up the flywheel and weight and remove any metal stuck to the magnets. 10. Install the flywheel with weight back onto the tapered crank shaft end making sure the key ways are lined up. Torque the stock nut to 42 ft- lbs.

18SP666 – MBE 900 Pilot Bearing Bolt Service Kit (P/N ... - DDCSN

New flanged multi-point socket head bolts have been released to prevent the MBE 900 pilot bearing from walking out of the flywheel housing. The new bolts will replace two flywheel bolts, located 180 degrees from one another. KIT CONTENTS The MBE 900 Pilot Bearing Bolt Service Kit P/N: A9269900105, consists of the following parts, listed in Table 1: Part No. A9269900005 18SP666 Table 1 Qty. 2 1 Description Flanged Multi-point Socket Head Bolts Installation Instructions MBE 900 Pilot Bearing Retaining Bolt Service Kit (P/N: A9269900105) INSTALLATION PROCEDURE Use the following procedure to install the new flanged multi-point socket bolts: 1. Shut off engine and apply the parking brake, chock the wheels, disconnect vehicle battery power, and perform any other applicable safety steps. 2. Remove the transmission. 3. Remove clutch from flywheel. 4. Pull the crankshaft position sensor out of the flywheel housing about 8 mm (0.32 in.). 5. Remove the end cover from the flywheel housing and install the engine barring tool (J-46392). Tighten the bolts on the barring device to 25 N·m (18 lb·ft). Insert the locking pin to block the device and prevent it from rotating. 6. Using J-46385, the flywheel and main pulley socket tool, remove two flywheel multi-point socket head bolts from the flywheel, 180 degrees apart. See Figure 1.

a Wall Street Journal piece
by MitraKalita 0 Comments favorite 6 Viewed Download 0 Times

Presbyterians Join the Anti-Israel Choir Divesting from companies like Motorola Solutions to show solidarity with the Palestinians. By Jonathan Marks June 22, 2014 6:34 p.m. ET The Presbyterian Church (U.S.A.) is bleeding members. Between 2000 and 2013, almost 765,000 members left the organization, a loss of nearly 30%. Last week the church's leadership met in Detroit for crisis talks. No, not about the emptying-pews crisis. The Israel-Palestinian crisis. On Friday, in a close vote (310-303), the General Assembly of the Presbyterian Church (U.S.A.)— the largest of several Presbyterian denominations in America—resolved to divest the organization's stock in Caterpillar, Hewlett-Packard and Motorola Solutions. The church's Committee on Mission Responsibility Through Investment said the companies have continued to "profit from their involvement in the occupation and the violation of human rights in the region," and have even "deepened their involvement in roadblocks to a just peace." Israel's counterterrorism and defense measures have included razing Palestinian houses (with Caterpillar equipment), operating Gaza and West Bank checkpoints (with Hewlett-Packard technology), and utilizing military communications and surveillance (with Motorola Solutions technology). The church signaled its antipathy for Israel earlier this year by hawking a study guide called "Zionism Unsettled" in its online church store. In the 76-page pamphlet, Zionism—the movement to establish a Jewish homeland and nation-state in the historic land of Israel—is characterized as a "a struggle for colonial and racist supremacist privilege." In a postscript to "Zionism Unsettled," Naim Ateek, a Palestinian priest and member of the Anglican Church, explains the meaning of the charges in the pamphlet.

VW Amarok - Body Harness.pdf - Hayman Reese

For P/No: 04998 & 04999 only. 1. In the engine bay, disconnect the negative and positive battery terminals. 2. Remove the vehicle battery (1) by first removing any fasteners. 3. Locate the vehicle grommet behind the battery cavity area. 4. Pierce a hole in the vehicle grommet. Note: Do not connect the harness to the battery at this point. Issue Date 27-09-10 For P/No: 04997 only. 5. In the engine bay, locate the vehicle battery (1). 6. Route the body harness (2) down through to the chassis. Note: Do not connect the harness to the battery at this point. 7. Route the power input harness (1) from the engine bay down through to the chassis, following the path of the brake and fuel lines. For P/No: 04997 & 04999 only. 8. Following the diagram on the right, house the two power & ground input harness female terminals (4) into the mating connector (3). 9. Connect the power input harness connector (3) to the body harness mating connector. Issue Date 27-09-10 For P/No: 04998 only. 10. Following the diagram on the right, house the three power & ground input harness female terminals (4) into the mating connector (5). 11. Connect the power input harness connector (5) to the body harness mating connector. 12. Route the body harness (1) along the LHS chassis rail, following the path of the blue vehicle harness towards the rear of the vehicle. 13. Route the body harness (1) along the rear of the vehicle towbar towards the towbar mounting bracket. Issue Date 27-09-10

955.421.020.99.CSB
by Maradoni 0 Comments favorite 18 Viewed Download 0 Times

These instructions only apply to this particular version center support bearing and may not be correct for other versions. TOOLS NEEDED: • Ratchet • 12mm serrated wrench (triple square bit) – NAPA # SER2306 • 13mm socket • 18mm socket • 6 inch extension • 18mm open end wrench • Rubber mallet or dead blow hammer. . Expanding flat nosed snap ring pliers . Various other common hand tools INSTRUCTIONS: Read these entirely and understand them BEFORE you attempt this procedure. 1. Apply parking brake and wheel chocks to prevent vehicle from rolling. A lift is recommended for this repair. IMPORTANT: Carefully mark driveshaft orientation on both ends of shaft sections. (Transmission and differential ends, as well as splined ends where the two drive shafts come apart to allow removal of center support) The sections MUST be reassembled EXACTLY as they came apart for the removal of the old center support bearing, and the driveshaft needs to be reinstalled EXACTLY the same way, in the exact same orientation. Failure to do so can result in imbalance, vibration, and potential damage to vehicle. Otherwise a professional drive shaft shop must be employed to re-balance entire assembly. 2. Remove 6 10mm bolts at joint at rear of back driveshaft. Use the M12 triple square (12point) tool. (NAPA part number SER2306). 3. Remove 3 18mm wrench size (12mm bolt size) bolts from front of driveshaft. 4. Remove 3 18mm wrench size (12mm bolt size) bolts on flex disc. 5. Remove 13mm wrench size (8mm bolt size) bolts on plate covering center support. 6. On some models (Turbos), it may be necessary to loosen various exhaust system clamps, hangers and components to ease access to driveshaft. 7. Pull driveshaft toward front of vehicle to separate it from differential.

« previous  123456789