SEARCH

Found 9667 related files. Current in page 1

how to remove manual transmission on 1995 4x4 nissan pickup

Technical Bulletin - JASPER Engines & Transmissions

Interference Between Clutch Damper and Flywheel Bolts On 2003-2006 Caterpillar 3406E C-15 & C-16 Diesel Engines The AERA Technical Committee offers the following information regarding possible interference between the clutch damper and flywheel bolts on 2003-2006 Caterpillar 3406E, C-15 and C-16 diesel engines. Engines built or serviced with the VCT plus clutch damper, introduced in April 2003, have the possibility of the clutch damper interfering with the flywheel mounting bolts. This applies to the following clutch part numbers: 108009-32Y, 108925-20, 108925-25, 108926-20Y, 108926-25Y, 109701-20, 109701-25, 109705-20Y, 109705-25Y & 109706-32Y. Correction/Action: Any repair that has required the transmission to be removed from the truck, and the engine serial number is 5EK1 and up, 6TS1 and up, 1LW1 and up, 2WS1 and up, 6NZ1-92122, 7CZ1-04382, MBN1-21447, BXS1-00984, 5DS1 and up, or 1MM1 and up, requires checking the flywheel bolt washers. You must verify the 5mm washer has been replaced with the 3mm washer, Caterpillar Part Number 8D-5054. Failure to replace the washers could result in damper rivet interference. Torque the bolts to 270 Nm +/- 40 Nm (200 ft/lb +/- 30 ft/lb). It is also suggested that paint may be applied to bolt heads to show verification and completion identification.

520 CRF 150R and 625 KX 450F 06-08 Flywheel ... - Steahly Offroad

Installation Instructions for CRF 150R and KX450F Steahly Flywheel Weight Warning: Improper instalation of this flywheel weight could result in engine damage or a serious crash. If you do not have the tools or the mechanical abilities take it to a professional. 1. Drain the engine oil or turn off the gas and lay the bike on its side. 2. Remove the shift lever. 3. Remove the ignition cover. Take care not to tear the gasket or have a new gasket on hand. Be carefull that you don’t lose the two dowel pins that are between the cover and the engine case. 4. Remove the flywheel nut. Use an air impact wrench or figure out a way to keep the flywheel from rotating while you remove the nut. A strap wrench or an automotive oil filter wrench may work as a holding tool or try putting the bike in high gear and holding the rear brake on. 5. Pull off the stock flywheel with the proper flywheel puller that has a crank end protection cap. Steahly part number E-63. Do not attempt removal with out the correct puller. Do not use claw type pullers. 6. Fit the flywheel weight on to the stock flywheel. Line up the two threaded holes in the weight with two holes in the stock flywheel. 7. Clean the threads of the two special bolts with contact cleaner. Put a big drop of red Loctite or other high strength thread locker on the threads of the 2 bolts. Install the two special bolts as shown in the picture and torque to 12 foot pounds. 8. Unless you plan to take the weight on and off a lot we highly recommend using a center punch and a hammer to flare out the threads at the end of the bolt (see pictures below). This will reduce the possibility of the bolt coming loose. 9. Clean up the flywheel and weight and remove any metal stuck to the magnets. 10. Install the flywheel with weight back onto the tapered crank shaft end making sure the key ways are lined up. Torque the stock nut to 42 ft- lbs.

Installation of Flywheel - DDCSN
by Prezta 0 Comments favorite 6 Viewed Download 0 Times

[b] If clutch contact face is scored or worn, the flywheel may be refaced. [c] If clutch contact face is cracked, the flywheel must be replaced. NOTE: Do not remove more than 0.508 mm (0.020 in.) material from the flywheel. Maintain all of the radii when resurfacing. 2. Inspect the ring gear. [a] Check ring gear for excessively worn or damaged gear teeth. [b] If damaged gear teeth are detected, replace the ring gear. Refer to Section 1.15.3. 3. Inspect crankshaft and flywheel contact surface. [a] Check the butt end of the crankshaft and flywheel contact surface for fretting, brinelling, or burrs. See Figure 1-212. [b] Lightly stone the contact surface to remove any fretting, brinelling, or burrs. Figure 1-212 1.14.3 Crankshaft and Flywheel Mating Surfaces Installation of Flywheel Install the flywheel as follows: 1. Install two flywheel guide studs, J 36235, into two of the tapped holes in the crankshaft at the 3 and 9 o’clock position. 2. Attach the flywheel lifting tool and, using a chain hoist, position the flywheel in the flywheel housing. Align the flywheel bolt holes with the crankshaft bolt holes. All information subject to change without notice. (Rev. 2004) 6SE50 0403 Copyright © 2004 DETROIT DIESEL CORPORATION From Bulletin 2-50-04 1-261 1.14 FLYWHEEL NOTICE: A new scuff plate must be used whenever the flywheel is removed. Failure to replace the scuff plate may cause the flywheel bolts to loosen, even when torqued correctly. 3. Using a new scuff plate, install two bolts with International Compound #2® (or equivalent) through the plate 180 from each other. 4. Install the flywheel lock, J 36375–A. See Figure 1-195. 5. Remove the flywheel lifting tool and guide studs. 6. Apply International Compound #2® (or equivalent) to the threads and to the bolt head contact area (underside) of the remaining bolts. The bolt threads must be completely filled with International Compound #2® (or equivalent). Any excess must be wiped off. See Figure 1-213.

The torque turn specification for the flywheel to crankshaft bolts has ...

Additional service information is available in the Detroit Diesel Series 60 Service Manual, 6SE483. The next revision to this manual will include the revised information. As a convenience to holders of the Series 60 Service Manual, information in service manual format is attached. The page(s) may be inserted into the manual. NOTE: Manual insert pages are numbered for insertion into the current Series 60 Service Manual dated January 2004. Service manuals are available from authorized Detroit Diesel distributors. If this bulletin was obtained from the Internet, service manual page(s) are available by returning to the screen “SIB Index”, selecting attachment pages, and printing the page(s). Detroit Diesel®, DDC®, Series 60® and the spinning arrows design are registered trademarks of Detroit Diesel Corporation. © Copyright 2004 Detroit Diesel Corporation. All rights reserved. Printed in U.S.A.

18SP666 – MBE 900 Pilot Bearing Bolt Service Kit (P/N ... - DDCSN

New flanged multi-point socket head bolts have been released to prevent the MBE 900 pilot bearing from walking out of the flywheel housing. The new bolts will replace two flywheel bolts, located 180 degrees from one another. KIT CONTENTS The MBE 900 Pilot Bearing Bolt Service Kit P/N: A9269900105, consists of the following parts, listed in Table 1: Part No. A9269900005 18SP666 Table 1 Qty. 2 1 Description Flanged Multi-point Socket Head Bolts Installation Instructions MBE 900 Pilot Bearing Retaining Bolt Service Kit (P/N: A9269900105) INSTALLATION PROCEDURE Use the following procedure to install the new flanged multi-point socket bolts: 1. Shut off engine and apply the parking brake, chock the wheels, disconnect vehicle battery power, and perform any other applicable safety steps. 2. Remove the transmission. 3. Remove clutch from flywheel. 4. Pull the crankshaft position sensor out of the flywheel housing about 8 mm (0.32 in.). 5. Remove the end cover from the flywheel housing and install the engine barring tool (J-46392). Tighten the bolts on the barring device to 25 N·m (18 lb·ft). Insert the locking pin to block the device and prevent it from rotating. 6. Using J-46385, the flywheel and main pulley socket tool, remove two flywheel multi-point socket head bolts from the flywheel, 180 degrees apart. See Figure 1.

Eaton Heavy-Duty Clutches CLSM0200 - Roadranger

The major cause of clutch failure is excessive heat. Excessive heat generated between the flywheel, driven discs, intermediate plate and pressure plate can cause the metal to flow and the material to be destroyed. If this occurs, the clutch can burst which can cause property damage, serious bodily injury or death. In order to prevent clutch failure resulting from excessive heat: 1. Do not exceed recommended vehicle loads. 2. The clutch should only be used for the recommended applications. 3. Drivers should be properly trained in starting, shifting and operation of the clutch. 4. Drivers should report erratic clutch operation as soon as possible to permit maintenance personnel to inspect, adjust or lubricate as required. 5. The removal and installation procedure described for each component may vary for your vehicle. For Solo and Heavy-Duty ECA clutches only, install shipping bolts before removing clutch assembly from the flywheel. IMPORTANT For service information and assistance, call the Roadranger Help Desk at 1-800-826-HELP (4357) (Mexico: 01-800-826HELP (4357). You may also find more information about Eaton Clutches at www.Roadranger.com. Mechanics must be familiar with proper clutch adjustment, linkage adjustment, lubrication and other maintenance troubleshooting procedures outlined in the Failure Analysis Guide. Every effort has been made to ensure the accuracy of the information contained in this manual. However, Eaton Corporation makes no warranty, expressed or implied, based on the information provided.

1.9 CRANKSHAFT ASSEMBLY - DDCSN
by Prezta 0 Comments favorite 7 Viewed Download 0 Times

The crankshaft is precision-forged with seven main bearings and eight custom-forged counter weights, and a vibration damper at the front end. For an exploded view of the crankshaft, main bearings, and main bearing caps, see Figure 1-42. 1. Crankshaft 5. Lower Bearing Shell (center) 2. Upper Bearing Shell(s) 6. Main Bearing Cap(s) 3. Upper Bearing Shell (center) 7. Main Bearing Cap (center) 4. Lower Bearing Shell(s) 8. Main Bearing Cap Bolt Figure 1-42 Crankshaft, Main Bearings, and Main Bearing Caps All information subject to change without notice. (Rev. 3/04) 6SE412 0403 Copyright © 2006 DETROIT DIESEL CORPORATION From Bulletin 1–MBE4000–06 1-57 1.9 CRANKSHAFT ASSEMBLY 1.9.1 Crankshaft Removal Remove the crankshaft as follows: FALLING ENGINE To avoid injury from a falling engine, an adequate lifting device with a spreader bar and sling should be used to lift the engine. The sling and spreader bar should be adjusted so the lifting hooks are vertical to prevent bending the lifter brackets. To ensure proper weight distribution, all provided lifter brackets must be used. NOTICE: A spreader bar must be used at all times in conjunction with the front and rear lifter brackets to lift the EGR engine to ensure that no engine damage will result. The brackets are designed to lift vertically. 1. Remove the engine from the vehicle.

Multilingual Employee Handbooks: Speaking Clearly

http://www.aptranslation.com/ | Multilingual employee handbooks make your international and ESL employees feel like a part of the team and relay important information. Getting the right translation company to translate your policies and procedures into several languages is key to creating an accessible manual.

Xbox 360 Play and Charge Kit QUICK SETUP GUIDE - Rocketfish

Setting up Charging the rechargeable battery pack Setting up the rechargeable battery pack 1 Press the tab on the top of the controller’s battery compartment cover, then and pull down to detach the original battery from the controller. Charge your battery pack before its first use and whenever it is drained. 1 Insert the charging plug into the charge port on the front of your wireless controller. 2 Connect the USB plug to any USB port of your Xbox 360. 3 Turn on your console. The charge indicator on the front of the plug glows red as the battery pack charges. When the light glows green, the battery pack is fully charged. Rechargeable battery safety Incorrect battery use may result in battery leakage, overheating, or explosion. When using batteries, make sure that you follow these instructions: • Keep batteries out of reach of children. • Do not heat, open, puncture, mutilate, or dispose of batteries in fire. • If a battery leaks, remove the battery, taking care to keep the leaked fluid from touching your skin or clothes. If fluid from the battery comes into contact with skin or clothes, flush skin with water or remove the clothing immediately. Before inserting a new battery, thoroughly clean the controller with a damp paper towel. • Do not allow metal objects to touch the battery terminals, because they can become hot and cause burns. For example, do not carry the battery in a pocket with keys or coins. • Remove the battery when the product will not be used for an extended period of time.

Just Cause 2 - Microsoft Xbox 360 - Manual ... - Games Database

A very small percentage of people may experience a seizure when exposed to certain visual images, including flashing lights or patterns that may appear in video games. Even people who have no history of seizures or epilepsy may have an undiagnosed condition that can cause these “photosensitive epileptic seizures” while watching video games. These seizures may have a variety of symptoms, including lightheadedness, altered vision, eye or face twitching, jerking or shaking of arms or legs, disorientation, confusion, or momentary loss of awareness. Seizures may also cause loss of consciousness or convulsions that can lead to injury from falling down or striking nearby objects. Immediately stop playing and consult a doctor if you experience any of these symptoms. Parents should watch for or ask their children about the above symptoms— children and teenagers are more likely than adults to experience these seizures. The risk of photosensitive epileptic seizures may be reduced by taking the following precautions: Sit farther from the screen; use a smaller screen; play in a well-lit room; do not play when you are drowsy or fatigued. If you or any of your relatives have a history of seizures or epilepsy, consult a doctor before playing.

« previous  123456789