SEARCH

Found 3222 related files. Current in page 12

ford radio pin diagram

AIR HORNS FOR HARLEY-DAVIDSON INSTALLATION ...

Remove the stock horn and bracket from the stud it is mounted to and unplug the 2 wires. Remove the seat. Route the end of the wire and hose loom without the connectors. Starting in front of the fuel valve, route this loom behind the valve, over the fuel line over the rear cylinder head along the existing wiring or hoses - if your model has any. Follow the frame to where the back bone and seat support rails come together. Route the loom up into the general area where the compressor will mount (i.e. see diagram). Attach the hose to the 'Y' connector on the horns themselves. Attach the two black wires from the loom to the relay terminals #87 and #30, located between the air horns behind chrome cover. Attach the wires from the original horn to the remaining terminals #85 and #86 (NOTE: it makes no difference which wire goes to which terminal). Attach the relay to the back of the horn bracket assembly or up under the fuel tank using the small cable tie provided. NOTE: the terminals must point downward to prevent water from entering the relay! Install the horn assembly using the 1/4" thick chrome washer provided behind the horn mounting bracket. Use the original acorn nut and tighten securely. Check to see that the horns have at least 1/4" clearance between the engine, shift linkage and choke knob. They should be horizontal or angle down at the front just slightly. Take any slack out of the loom, keeping it up against the frame and away from the engine or exhaust, using several of the small cable ties provided.

Tech Bulletin - Harley Davidson - PAC Audio

techsupport@go2pac.com. RADIO AUDIO CONTROL. Cut here before the joint. Connect handlebar side to ground. 560. Connect this wire to SWC input of ... 1. On the [24A] connector, cut PK/W wire - pin #9, before the joint and connect the handle bar side to ground. Insulate the remaining wire. Note: Double check that the handle bar side is grounded and not the other side. 99% of technical calls is the result of the wrong pk/w wire side is grounded. 2. On the [27B] connector, splice PK/W - pin #3 and GN/BE - pin #23 together with a 47 ohm resistor inline. Splice GY/W - pin #4 and GY/GN together with a 150 ohm resistor inline. Splice V/BK - pin #5 and BN/BK - pin #8 together with a 1k resistor inline. Connect all remaining ends of resistors together and connect to SWC input wire of interface. 3. Connect BN/W - pin #6 to ground with a 560 ohm resistor inline. Pacific Accessory Corporation - 1502 S. Santa Fe Street, Santa Ana, CA 92705 www.go2pac.com Voice: 714-835-3022 Fax: 714-835-3233 techsupport@go2pac.com

wiring diagram ssvr-12 (12 volt) for harley davidson - Zodiac

231731/231904/731513 SSVR-12 (12 VOLT) FOR HARLEY DAVIDSON SSVR-12 is an all solid state voltage and current regulator designed expressly for Harley-Davidson two (2) brush generators. It offers greater reliability and smoother voltage regulation than the mechanical regulator it replaces. It will easily keep any electric or kick start battery charged at the correct rate. Its unique output will safely operate the lights WITHOUT the use of a battery if your motorcycle is equipped with a magneto ignition. Ideal for states that require lights on at all times. WARRANTY SSVR-12 is warranteed against circuit failure for 1 full year. It is made in Japan. GENERATOR and BATTERY Make sure brushes are good. Armature commutator must be clean. Battery terminals must be clean, acid up to level and a good ground connection. Be sure your battery will hold a charge and does not have an open or dead cell. If in doubt replace same. INSTRUCTIONS 1) Mount SSVR-12 to grounded part of bike where some air flow is possible. Do not rubber mount. 2) Locate (F) field and (A) armature markings stamped on top of generator case. 3) (a) Connect RED wire from SSVR-12 to (A) post on generator. (b) Connect GREEN wire from SSVR-12 to (F) post on generator. (c) Connect BLACK wire from SSVR-12 to positive (+) battery terminal or to battery position on switch. A 20 AMP fuse is recommended. 4) NO BATTERY operation, connect BLACK wire to light switch. WIRING DIAGRAM CHARGING LIGHT IF USED BLACK RED SSVR-12 20 AMP FUSE B IG GREEN + A F LT GEN. KEY SWITCH AMP METER IF USED BATT POLARIZE Generator MUST be polarized. Use jumper lead and momentarily touch positive battery terminal to (A) post on generator. WITHOUT battery, use the following procedure: Any battery with correct voltage may be used Ground negative (-) side of battery to frame, connect positive (+) side of battery to (A) post on generator momentarily. Generator is now polarized. Remove battery.

Cisco Small Business AP541N Dual-band Single-radio Access Point ...

AP541N Dual-band Single-radio Access Point Quick Start Guide Package Contents • Cisco AP541N Dual-band Single-radio Access Point that includes an IEEE 802.11a/b/g/n radio. • Three antennas (These might be black or black-and-silver. This does not affect performance.) • Screws and wallboard anchors • Cat 5e Ethernet cable • Power supply • This quick start guide • Product CD-ROM Welcome Thank you for choosing the Cisco Small Business AP541N. The Cisco AP541N, part of the Cisco Smart Business Communications System (SBCS), is an 802.11n wireless access point purposely built for the Small Business. This guide is designed to familiarize you with the general layout of the access point, how to deploy the device in your network, and access the configuration interface. Your access point has more features or functionality than what is described in this guide. For additional configuration information, see the Cisco AP541N Administration Guide available at http://www.cisco.com/en/US/products/ps10492/ prod_maintenance_guides_list.html. 1 Getting to Know the Cisco AP541N This section describes the exterior of the access point. Front Panel LEDs all Cisco Sm s Pro Busines t RESET PWR PoE DIAG SPEED LAN WLAN 2.4G Cisco AP541N Dual-band Single-radio Access Point Quick Start Guide Access Poin 235174 Radio d Single Dual Ban AP54 1N WLAN 5G 1 CAUTION Before you connect your access point to the network or power it on, read the “Getting Started with the Configuration” section....

a climate risk assessment for the united states - Risky Business

RISKY BUSINESS: The Economic Risks of Climate Change in the United States A Product of the Risky Business Project: Co-Chairs: Michael R. Bloomberg, founder, Bloomberg Philanthropies; 108th Mayor of the City of New York; founder, Bloomberg L.P. Henry M. Paulson, Jr., Chairman of the Paulson Institute; former U.S. Secretary of the Treasury Thomas F. Steyer, retired founder, Farallon Capital Management LLC Risk Committee Members: Henry Cisneros, Founder and Chairman, CityView Capital; former U.S. Secretary of Housing and Urban Development (HUD); former Mayor of San Antonio Gregory Page, Executive Chairman, Cargill, Inc. and former Cargill Chief Executive Officer Robert E. Rubin, Co-Chairman, Council on Foreign Relations; former U.S. Secretary of the Treasury George P. Shultz, Thomas W. and Susan B. Ford Distinguished Fellow at the Hoover Institution; former U.S. Secretary of State; former U.S. Secretary of the Treasury; former U.S. Secretary of Labor; former Director, Office of Management and Budget; former President, Bechtel Group Donna E. Shalala, President, University of Miami; former U.S. Secretary of Health and Human Services Olympia Snowe, former U.S. Senator representing Maine Dr. Alfred Sommer, Dean Emeritus, Bloomberg School of Public Health; University Distinguished Service Professor, Johns Hopkins University © 2014 Risky Business

CAUTION: Zoom N' Go HULK™ ATV 4-Wheeler - Hasbro

Zoom N’ Go HULK™ ATV 4-Wheeler To install batteries: 1. Using a Phillips/cross head screwdriver (not included), unscrew battery cover. 2. Insert 2 fresh 1.5 V “AA” or LR6 batteries. See diagram for polarity. 3. Replace battery cover and tighten screw. IMPORTANT: BATTERY INFORMATION Please retain this information for future reference. Batteries should be replaced by an adult. CAUTION: TO AVOID BATTERY LEAKAGE 1. Be sure to insert the batteries correctly and always follow the toy and battery manufacturers’ instructions; 2. Do not mix old and new batteries or alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium) batteries; 3. Always remove weak or dead batteries from the product. CAUTION: 1. Always follow the instructions carefully. Use only batteries specified and be sure to insert item correctly by matching the + and – polarity markings. 2. Do not mix old and new batteries or standard (carbon-zinc) with alkaline batteries. 3. Remove exhausted or dead batteries from the product. 4. Remove batteries if product is not to be played with for a long time. 5. Do not short-circuit the supply terminals. 6. Should this product cause, or be affected by, local electrical interference, move it away from other electrical equipment. Reset (switching off and back on again or removing and reinserting batteries) if necessary. 7. RECHARGEABLE BATTERIES: Do not mix these with any other types of batteries. Always remove from the product before recharging. Recharge batteries under adult supervision. DO NOT RECHARGE OTHER TYPES OF BATTERIES.

Ovi Isilovci su frakcija Sirijskih pobunjenika koja je najmilija SAD finansiraju ih iz S.Arabije,a vecina vodja su iz Jordana

moze se reci da je islamisicki zar Jordanaca prilicno splasnuo.Na pocetku Arapskog proleca u Egiptu,pre vise od 3 god.,svakod petka,od Huseini dzamije u (starom ) centru grada,ispod mog prozora takoreci,isle su demonstracije Brace,posle nekog vremena u vojnom poretku,sa marsiranjem.Suk petkom (kad gradjani ne rade) nije radio,trgovci su dezurali ispred svojih radnji,da ih ne opljackaju demonstranti,ali posle Morsijeve pobede-stvar je splasnula,mada se ocekivalo obrnuto.

2004 FORD F150 w/ 5.4L 3” BODY LIFT KIT INSTALLATION ...

This body lift kit should only be installed on vehicles in good working condition. Before installation, the vehicle should be thoroughly inspected for evidence of corrosion or deformation of the sheet metal around the factory body mounts. This body lift kit should not be installed on any vehicle that is suspected to have been in a collision or misused. Off road use of your vehicle with this body lift kit installed may increase the stress applied to the factory body mounts. We do not recommend that any vehicle with a body lift installed be involved in any extreme off road maneuvers such as jumping. Failure to observe this warning may result in serious personal injury and/or severe damage to your vehicle. 2004 FORD F150 w/ 5.4L WARNING Many states now have laws restricting bumper heights and vehicle lifts. Local laws should be consulted to determine if the changes you intend to make to your vehicle comply with state laws. Before combining a body lift with a suspension lift, consult an installation professional to see how this will affect your specific application. (Except Heritage) 3” BODY LIFT KIT INSTALLATION INSTRUCTIONS KIT #70063 WARNING WARNING Installation of a Performance Accessories body lift kit will change the center of gravity and the handling characteristics of the vehicle. Because of the higher center of gravity and larger tires, the vehicle will handle and react differently both on and off road. You must drive it safely! Extreme care must be taken to prevent vehicle rollover or loss of control, which could result in serious injury or death. Avoid sudden sharp turns or abrupt maneuvers and always make sure all vehicle occupants have their seat belts fastened. The installation of larger wheel and tire combinations may reduce the effectiveness of the Anti-lock Braking System. WARNING Always wear eye protection when operating power tools. WARNING Ensure that your vehicle tires are properly blocked and secured before you begin installation of this lift kit.

FORD F150 BODY LIFT KIT INSTALLATION INSTRUCTIONS 2003 ...

This kit should only be installed on a vehicle that is in good working condition. Before you install the kit, thoroughly inspect the vehicle for corrosion or deformation of the sheet metal around the factory body mounts. If the vehicle is suspected to have been in a collision or misused, do not install this kit. Off-road use of your vehicle with this kit installed may increase the stress applied to the factory body mounts. We do not recommend that any vehicle with a body lift kit installed be involved in any extreme off-road maneuvers such as jumping. Failure to observe this warning may result in serious personal injury and/or severe damage to your vehicle. WARNING Many states and municipalities have laws restricting bumper heights and vehicle lifts. Consult state and local laws to determine if the changes you intend to make to the vehicle comply with the law. WARNING Installation of a Performance Automotive Group body lift kit will change the vehicle’s center of gravity and handling characteristics both on- and off-road. You must drive the vehicle safely! Extreme care must be taken to prevent vehicle rollover or loss of control, which could result in serious injury or death. Avoid sudden sharp turns or abrupt maneuvers and always make sure all vehicle occupants have their seat belts fastened. WARNING The installation of larger tires may reduce the effectiveness of the braking system. WARNING Always wear eye protection when operating power tools. WARNING Before you install this kit, read and understand all instructions, warnings, cautions, and notes in this instruction sheet and in the vehicle owner’s manual. WARNING Before you install this kit, block the vehicle tires to prevent the vehicle from rolling.

C-Class - Mercedes-Benz USA
by Paffett 0 Comments favorite 13 Viewed Download 0 Times

Order no. 6515079413 Part no. 2045843383 Edition A 2014 C-Class É2045843383ÁËÍ 2045843383 Symbols Registered trademarks: i Practical tips or further information that RBluetooth® X is a registered trademark of Bluetooth SIG Inc. RDTS is a registered trademark of DTS, Inc. RDolby and MLP are registered trademarks of DOLBY Laboratories. RBabySmart™, ESP® and PRE-SAFE® are registered trademarks of Daimler AG. RHomeLink® is a registered trademark of Johnson Controls. RiPod® and iTunes® are registered trademarks of Apple Inc. RLogic7® is a registered trademark of Harman International Industries. RMicrosoft® and Windows media® are registered trademarks of Microsoft Corporation. RSIRIUS is a registered trademark of Sirius XM Radio Inc. RHD Radio is a registered trademark of iBiquity Digital Corporation. RGracenote® is a registered trademark of Gracenote, Inc. RZAGATSurvey® and related brands are registered trademarks of ZagatSurvey, LLC. In this Operator's Manual you will find the following symbols: could be helpful to you. This symbol indicates an instruction that must be followed. Several of these symbols in X succession indicate an instruction with several steps. (Y page) This symbol tells you where you can find more information about a topic. This symbol indicates a warning or YY an instruction that is continued on the next page. Display This font indicates a display in the multifunction display/COMAND display. Parts of the software in the vehicle are protected by copyright © 2005 The FreeType Project http://www.freetype.org. All rights reserved. Publication details Internet Further information about Mercedes-Benz vehicles and about Daimler AG can be found on the following websites: http://www.mbusa.com (USA only) http://www.mercedes-benz.ca (Canada only) Editorial office ©Daimler AG: Not to be reprinted, translated or otherwise reproduced, in whole or in part, without written permission from Daimler AG. Vehicle manufacturer Daimler AG Mercedesstraße 137 70327 Stuttgart Germany G WARNING Warning notes make you aware dangers which could pose a threat to your health or life, or to the health and life of others. H Environmental note Environmental notes provide you with information on environmentally aware actions or disposal. ! Notes on material damage alert you to dangers that could lead to damage to your vehicle. As at 15.11.2012 Welcome to the world of Mercedes-Benz We urge you to read this Operator's Manual carefully and familiarize yourself with the vehicle before driving. For your own safety and a longer vehicle life, follow the instructions and warning notices in this manual. Ignoring them could result in damage to the vehicle or personal injury to you or others. Vehicle damage caused by failure to follow instructions is not covered by the MercedesBenz Limited Warranty. The equipment or product designation of your vehicle may vary depending on: RModel ROrder RCountry specification RAvailability Mercedes-Benz therefore reserves the right to introduce changes in the following areas: RDesign REquipment RTechnical features The equipment in your vehicle may therefore differ from that shown in the descriptions and illustrations.

 8910111213141516