SEARCH

Found 1742 related files. Current in page 1

diagramas de escalera motor a pasos

Stage 1 Clutch Kit Installation
by Prezta 0 Comments favorite 4 Viewed Download 0 Times

This tutorial is provided as a courtesy by ECS Tuning. Proper service and repair procedures are vital to the safe, reliable operation of all motor vehicles as well as the personal safety of those performing the repairs. Standard safety procedures and precautions (including use of safety goggles and proper tools and equipment) should be followed at all times to eliminate the possibility of personal injury or improper service which could damage the vehicle or compromise its safety. Although this material has been prepared with the intent to provide reliable information, no warranty (express or implied) is made as to its accuracy or completeness. Neither is any liability assumed for loss or damage resulting from reliance on this material. SPECIFICALLY, NO WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR ANY OTHER WARRANTY IS MADE OR TO BE IMPLIED WITH RESPECT TO THIS MATERIAL. In no event will ECS Tuning, Incorporated or its affiliates be liable for any damages, direct or indirect, consequential or compensatory, arising out of the use of this material. VW Jetta MKIV Stage 1 Clutch Kit Installation

XBugBot - FlowStone
by JonyB 0 Comments favorite 3 Viewed Download 0 Times

This project came about when trying to make a low cost autonomous robot for use in education. The idea being that students would be able to identify with the Xbox controller and enjoy hacking it into something far more interesting! The Concept: This was a concept to make a low cost autonomous programmable robot for education using low cost every day things that the students could identify with – ie. The Xbox Controller. There are of course several existing product in this market most notably the Lego NXT and the Vex Systems. Both of these allow users to build and program autonomous robots, but there are two key differences, 1) On the XBugBot the programming and the processor are not separate! 2) The price! The XBugBot can be build for around 1/10th of the cost of the competing products! The humble Xbox Controller. What is the Xbox controller? Well once connected to the PC it becomes a low cost wireless DAQ (Data Acquisition System), it has several digital inputs (Buttons) and several analogue inputs (Joy Sticks etc.), plus two motor control outputs (Vibration Motors). What can it become? - Meet XBugBot: Hack your Xbox Controller and add a couple of wheels and sensors and you get an XBugBot! How is it Controlled? Using the FlowStone graphical programming language from DSPRobotics: (www.dsprobotics.com ) FlowStone is an awesome teaching tool for science, technology, engineering and mathematics (STEM) as is graphical so students can easily relate and understand it. Also the Xbox Controller is already pre-programmed into FlowStone so you can just use the Xbox Module and start programming your Bot. Programming and Processor:...

PRODUCT REVIEW > Volkswagen Amarok Canyon - Barry Maney ...

Volkswagen Amarok Canyon The most exciting Amarok model to hit Australian roads has finally arrived. Based on the Amarok TDI400/420 Highline, the Canyon delivers high levels of standard equipment, plus cutting edge design elements and features, including sports and side bars, new “Roca” alloys with AT-R tyres and two-tone Nappa Leather. Unique features and specification include: - Black gloss sports and side bars 17” Roca Alloy wheels with Pirelli Scorpion AR-R Tyres Two-tone Nappa Leather with orange interior highlights RNS315 Satellite Navigation with Rear-view Camera Load area coating (impact & UV resistant) Tinted tail lamps and Canyon rear & side decals Unique communication colour – Copper Orange To find out more about the Amarok Canyon Edition and your chance to win a cut of $250,000 of Stihl Power Tools call Bruce or Nathan on (08) 87213400 today. Barry Maney Group Motor eTorque – April 2014

iPod nano Manual del usuario - Support - Apple

Contenido. 5. Capítulo 1: El iPod nano de un vistazo. 5. Descripción general del iPod nano. 5. Accesorios. 6. Pantalla de inicio. 8. Iconos de estado. 9. Capítulo ... Descripción general del iPod nano Accesorios Pantalla de inicio Iconos de estado Cómo configurar el iPod nano Cómo utilizar Multi-Touch Cómo obtener información acerca del iPod nano Cómo conectar y desconectar el iPod nano Acerca de la batería Ajustar las preferencias Para organizar los iconos en la pantalla de inicio Sincronizar por primera vez Sincronización automática o manual Cómo transferir el contenido adquirido a otro ordenador Cómo reproducir música Cómo reproducir podcasts, audiolibros y colecciones de iTunes U Controlar el volumen Cómo crear listas de reproducción en el iPod nano Cómo utilizar los auriculares Apple Earphones Cómo escuchar la radio FM Cómo sintonizar la radio FM Cómo poner en pausa la emisión de radio en directo Etiquetado de canciones para la sincronización con iTunes Cómo ajustar la región de radio Cómo usar el iPod nano para contar los pasos Crear entrenamientos con música Cómo calibrar el iPod nano Ver y gestionar los datos de ejercicio

iPod nano Manual del usuario - Support - Apple

Accesorios El iPod nano viene con los accesorios siguientes: EarPods de Apple Cable Lightning a USB Utilice el cable Lightning para conectar el iPod nano al ordenador, sincronizar el contenido y cargar la batería. También puede utilizar el cable con el adaptador de corriente USB de Apple (se vende por separado). Utilice los auriculares Apple EarPods para escuchar música, audiolibros y podcasts. Estos auriculares también sirven de antena para escuchar emisiones de radio. Para obtener información acerca del uso de accesorios con el iPod nano, incluidos auriculares con micrófono opcionales y dispositivos Bluetooth®, consulte Capítulo 12, Auriculares EarPods y accesorios Bluetooth, en la página 57. Pantalla de inicio Cuando se enciende el iPod nano, aparece la pantalla de inicio. Pulse un icono en la pantalla de inicio para abrirlo; a continuación, utilice gestos para desplazarse (consulte en la página 9). Aparecerán los siguientes iconos de la pantalla de inicio la primera vez que encienda su iPod nano: Música Proporciona un acceso rápido a su música y otros contenidos sonoros organizados por listas de reproducción, artistas, canciones y otros. Vídeos Proporciona acceso rápido a sus películas y vídeos, organizados según el tipo. Ejercicio Abre la función Ejercicio, con la que puede contar los pasos si corre o camina y registrar el tiempo, la distancia, el ritmo y las calorías quemadas durante los entrenamientos. Podcasts Muestra los podcasts sincronizados con la biblioteca de iTunes. Fotos Muestra las fotos sincronizadas con el ordenador. Radio Abre el sintonizador de radio FM si se conectan los auriculares Apple EarPods o de otro tipo al iPod nano. Deslice el dedo hacia la izquierda para ver estos iconos adicionales en una segunda pantalla: Reloj Ajustes Abre el reloj, el cronómetro y el temporizador. Abre los ajustes del iPod nano y muchas de sus funciones. Capítulo 1    El iPod nano de un vistazo

How to measure driveshaft angles - Pirate4x4.Com

Cardan (cross) type universal joint operation is typically designed to be in a range of 1 to 3°, figure 1. A cardan type joint can operate for short periods of time at angles up to approximately eight degrees. Angles that are not within the desired range will cause drive line vibration and significantly shorten the life of the universal joint. Vibration that is created by incorrect u-joint angles is usually most noticeable at low speeds, under 40 mph., under load or acceleration. If a problem with u-joint angle is suspected perform the following basic inspection procedures. 1. Rotate the drive shaft to check for binding, or misalignment of the cross or bearing cups. 2. Check that all surfaces are clean. 3. Check the condition of the motor and transmission mounts. Broken mounts are a frequent cause of drive shaft vibration and are often overlooked. If these conditions are satisfactory a preliminary check of angles can be made with an inclinometer. Before attempting to measure angles ensure that tire air pressure is correct, that the vehicle is at the correct trim (chassis) height, and the ground surface is level. 1. Measure the angle of the front slip yoke by placing the inclinometer on the bottom of the bearing cup, figure 2. Position the inclinometer on the clean flat surface of the bearing cup, level the bubble and note the reading. 2. Measure the drive shaft angle, as shown, and subtract the smaller number from the greater to determine the angle. 3. Repeat the same procedure on the rear u-joint and pinion input shaft.

Laine Engine Stand Drawings
by kororawa 0 Comments favorite 1 Viewed Download 0 Times

4.00x4.50x1/4" steel caster mounts - 3/8" holes on 2.75x3.25 centers 2x2x.083 steel square tubing 2.000 Engine Stand, Main Frame 60.000 1" square tubing 7.750 4.000 30.000 30.000 truncate corner approx .5" .625 .500 Dia (2 pl) 7.200 4.563 .438 Dia * 8.250 7.625 1.688 .250 *Center hole is shown as corrected (original was 3/16 up and 3/16 left) Install CarQuest MOU 31-3097 motor mounts with studs towards center (78-79 Buick/Olds, 79 Chev, 75-76 Pontiac Transmission Mount) .875 See Mountbar.dc for main bar dims Mtl: 1.5 x 2.5 x .187 steel 1.500 Mount is to place crankshaft 10" above main frame 1.000 14.750 2.500 12.750 7.313 3.750 .438 Dia Small Block Ford Front Engine Mount Bar (mountbarSBFfront.dc) 2.000 4.750 .000, .000 2.875, -0.500 Matl: 1x1 tubing 3.375, -1.000 .500, -0.500 Generic Engine Mount Bar (mountbar.dc) .000, .000 28.500, -1.000 .438 Dia (typical) 2.875, -1.000 .500, -1.000 Matl: 2x2, .120 wall, square tubing 30.875, -1.000 CL = 15.687 31.375, -2.000 MountBarFordRear.dc Supports GM T-10, T5 and Tremec .500 R .000, .000 10.120, -1.000 1.880, -1.000 Matl: .375 al plate 1.750, -1.067 10.250, -1.067 6.000, -3.000 1.990, -1.530 9.910, -1.530 .500 Dia (9 pl) 1.120, -5.810 10.250, -5.810 1.000 .377 10.250, -7.377 1.750, -7.377 tap thru 3/8-16 (3 pl) .800 .500, -8.000 6.000, -8.000 2.440, -7.800 8.760, -7.800 11.500, -8.000 1.000 1.623 12.000, -9.000 .438 Dia Matl: 2x2x.125 angle 2.000 1.250 3.000 9.000 12.000 1.000 .438 Dia 10.813 14.563 16.813 20.563 Install CarQuest MOU 31-3097 motor mounts (78-79 Buick/Olds, 79 Chev, 75-76 Pontiac Transmission Mount) See Mountbar.dc for main bar dims Mount is to place crankshaft 10" above main frame .000, .000 1.000 2.000, -.500 .201 Dia (6 pl) 9.020, -1.860 1.625, -1.860 23.000, -.500 12.500, -.500 22.375, -1.750 12.000, -3.688 2.125, -2.235 .500 Dia 2.187, -2.297 Corners for .125 end mill 8.438, -5.438 23.250, -2.500 16.250, -2.500 16.250, -5.500 19.250, -2.500 21.500, -2.500 19.250, -5.500 8.500, -5.500 1.000 .156 Dia (4 pl) 9.020, -5.500 1.625, -5.500 21.500, -6.400 3.375 Dia .125 Dia (4 pl) 2.062 Dia (4 pl) 2.000, -7.375 .750 23.000, -7.375 12.500, -7.375 25.000, -7.750 MountBarDashPanel 23.250, -6.400 2x2x.083 steel square tubing. 4.00x4.50x1/4" steel caster mounts - 3/8" holes on 2.75x3.25 centers. 4.000. 7.750. 1" square tubing. Engine Stand, Main Frame ...

Twin cam 88™ engine stand Instruction Sheet For Tool No ... - Jims

These bolts are on OEM engine/ transmission assembly. 3. Use two 3 / 8” - 16 x 1 3/4” bolts with nuts to anchor front of motor to stand. Rev a. 3/00. No.1022-IS. Instruction Sheet For Tool No.1022 Twin cam 88™ engine stand use on all twin cam 88™ except 2000 & later softail Refer to H.D.® Service Manual for specifications 1. Can be mounted to bench with the four holes provided in the two legs. 2. Use two 3 / 8” - 16 x 2” bolts to anchor to rear of motor in slots. These bolts are on OEM engine/ transmission assembly. 3. Use two 3 / 8” - 16 x 1 3/4” bolts with nuts to anchor front of motor to stand. CAUTION: Wear safety glasses. Excessive force may damage parts and tool. See JIMS® catalog for over 100 other top quality professional tools. The last tools you will ever need to buy. “From the Track... To the Street!” 555 Dawson Drive, Camarillo, CA 93012 Phone 805-482-6913 • Fax 805-482-7422 Rev a 3/00 No.1022-IS Instruction Sheet For Tool No.1022 Twin cam 88™ engine stand use on all twin cam 88™ except 2000 & later softail Refer to H.D.® Service Manual for specifications 1. Can be mounted to bench with the four holes provided in the two legs. 2. Use two 3 / 8” - 16 x 2” bolts to anchor to rear of motor in slots. These bolts are on OEM engine/ transmission assembly. 3. Use two 3 / 8” - 16 x 1 3/4” bolts with nuts to anchor front of motor to stand. CAUTION: Wear safety glasses. Excessive force may damage parts and tool. See JIMS® catalog for over 100 other top quality professional tools. The last tools you will ever need to buy. “From the Track... To the Street!” 555 Dawson Drive, Camarillo, CA 93012 Phone 805-482-6913 • Fax 805-482-7422

TRANSMISSION REMOVAL & INSTALLATION - A/T ... - LIL EVO

AUTOMATIC FWD MODELS REMOVAL 1) Remove battery and battery tray. On 3000GT, remove undercover(s). On Eclipse turbo, drain and remove intercooler. On all models, remove air cleaner and case. Raise and support vehicle. Remove wheels. Disconnect control cables at transaxle. Drain transaxle fluid. 2) On Mirage 1.6L, disconnect tension rod. On all models, disconnect neutral safety switch connector, oil cooler hoses and electrical connectors from transaxle. Disconnect speedometer cable and throttle control cable (if equipped). Remove starter motor. 3) On Galant models with electronically controlled suspension, remove air compressor and bracket. Disconnect front height sensor rod at lower control arm. 4) On all models, remove upper transaxle-to-engine bolts. Remove engine undercover (if equipped). On all models, remove drive axle shafts. See FWD AXLE SHAFTS article in DRIVE AXLES. Separate lower control arms from struts for access to axle shafts (if necessary). 5) Remove front exhaust pipe (if necessary). On Eclipse 4WD, Galant 4WD and 3000GT, remove right member and gusset. On 4WD models, separate transfer assembly from transaxle. Reference mark transfer assembly-to-drive shaft and remove transfer assembly. 6) On all models, remove transmission inspection (dust) cover. Place index mark on torque converter and drive plate for reassembly reference. Remove torque converter-to-drive plate bolts. Push torque converter away from engine into transaxle. 7) Support transaxle with jack. Remove transaxle mounts bolts, mounting brackets and remaining transaxle-to-engine bolts. Slide transaxle assembly to right and lower to remove. CAUTION: Ensure torque converter is fully seated in transaxle before installation. Always install new snap rings on inner constant velocity joints.

Universal Grinding Machine - Thin Section

Universal Grinding Machine for Rubbing and Thin Sections Housing: Made of stainless steel, stain-resistant and powder-coated. The mechanic parts are made from anodized aircraft aluminum. Drive: Particularly solid and high-class, extremely softly running brushless DC motor 100 VA, 24V with high torque. The rotational speed goes from 0 up to 300 rpm; infinitely variable speed regulation, smooth start with clockwise and anti-clockwise rotation. Automatic coolant system: Reversible from water off, water permanently on, water on only when grinding. Water collection pan: Made of stainless steel, height-adjustable with water discharge hose. The machine can be modified with grinding discs SystemAbele® or by means of optional magnetic discs within a few seconds for all polishing and grinding discs which are available on the market, having a diameter of 250 mm. Width: ca. 37cm Length: ca. 38cm Height: ca.27cm Weight: ca. 15kg Connections: Power supply 230V/24V, foot-operated connection, feed hose 3/4", drain hose 14mm A convenient foot switch is optional. When purifying 6 nozzles rinse sufficient water onto the grinding disc. The rubber lips remove the water 3 times with any rotation and the dirt is pushed to the sides. This process reduces wear of the grinding disc and prevents grooves in thin section. Rubbing Barely simple exchange of the self-centering discs within seconds Making thin sections Barely simple convertible to optional discs within seconds for using any magnetic discs of diameter 25 cm .

« previous  123456789