SEARCH

Found 4570 related files. Current in page 1

chevy silverado leer cap wiring harness for brake light

520 CRF 150R and 625 KX 450F 06-08 Flywheel ... - Steahly Offroad

Installation Instructions for CRF 150R and KX450F Steahly Flywheel Weight Warning: Improper instalation of this flywheel weight could result in engine damage or a serious crash. If you do not have the tools or the mechanical abilities take it to a professional. 1. Drain the engine oil or turn off the gas and lay the bike on its side. 2. Remove the shift lever. 3. Remove the ignition cover. Take care not to tear the gasket or have a new gasket on hand. Be carefull that you don’t lose the two dowel pins that are between the cover and the engine case. 4. Remove the flywheel nut. Use an air impact wrench or figure out a way to keep the flywheel from rotating while you remove the nut. A strap wrench or an automotive oil filter wrench may work as a holding tool or try putting the bike in high gear and holding the rear brake on. 5. Pull off the stock flywheel with the proper flywheel puller that has a crank end protection cap. Steahly part number E-63. Do not attempt removal with out the correct puller. Do not use claw type pullers. 6. Fit the flywheel weight on to the stock flywheel. Line up the two threaded holes in the weight with two holes in the stock flywheel. 7. Clean the threads of the two special bolts with contact cleaner. Put a big drop of red Loctite or other high strength thread locker on the threads of the 2 bolts. Install the two special bolts as shown in the picture and torque to 12 foot pounds. 8. Unless you plan to take the weight on and off a lot we highly recommend using a center punch and a hammer to flare out the threads at the end of the bolt (see pictures below). This will reduce the possibility of the bolt coming loose. 9. Clean up the flywheel and weight and remove any metal stuck to the magnets. 10. Install the flywheel with weight back onto the tapered crank shaft end making sure the key ways are lined up. Torque the stock nut to 42 ft- lbs.

18SP666 – MBE 900 Pilot Bearing Bolt Service Kit (P/N ... - DDCSN

New flanged multi-point socket head bolts have been released to prevent the MBE 900 pilot bearing from walking out of the flywheel housing. The new bolts will replace two flywheel bolts, located 180 degrees from one another. KIT CONTENTS The MBE 900 Pilot Bearing Bolt Service Kit P/N: A9269900105, consists of the following parts, listed in Table 1: Part No. A9269900005 18SP666 Table 1 Qty. 2 1 Description Flanged Multi-point Socket Head Bolts Installation Instructions MBE 900 Pilot Bearing Retaining Bolt Service Kit (P/N: A9269900105) INSTALLATION PROCEDURE Use the following procedure to install the new flanged multi-point socket bolts: 1. Shut off engine and apply the parking brake, chock the wheels, disconnect vehicle battery power, and perform any other applicable safety steps. 2. Remove the transmission. 3. Remove clutch from flywheel. 4. Pull the crankshaft position sensor out of the flywheel housing about 8 mm (0.32 in.). 5. Remove the end cover from the flywheel housing and install the engine barring tool (J-46392). Tighten the bolts on the barring device to 25 N·m (18 lb·ft). Insert the locking pin to block the device and prevent it from rotating. 6. Using J-46385, the flywheel and main pulley socket tool, remove two flywheel multi-point socket head bolts from the flywheel, 180 degrees apart. See Figure 1.

Xbox 360 Play and Charge Kit QUICK SETUP GUIDE - Rocketfish

Setting up Charging the rechargeable battery pack Setting up the rechargeable battery pack 1 Press the tab on the top of the controller’s battery compartment cover, then and pull down to detach the original battery from the controller. Charge your battery pack before its first use and whenever it is drained. 1 Insert the charging plug into the charge port on the front of your wireless controller. 2 Connect the USB plug to any USB port of your Xbox 360. 3 Turn on your console. The charge indicator on the front of the plug glows red as the battery pack charges. When the light glows green, the battery pack is fully charged. Rechargeable battery safety Incorrect battery use may result in battery leakage, overheating, or explosion. When using batteries, make sure that you follow these instructions: • Keep batteries out of reach of children. • Do not heat, open, puncture, mutilate, or dispose of batteries in fire. • If a battery leaks, remove the battery, taking care to keep the leaked fluid from touching your skin or clothes. If fluid from the battery comes into contact with skin or clothes, flush skin with water or remove the clothing immediately. Before inserting a new battery, thoroughly clean the controller with a damp paper towel. • Do not allow metal objects to touch the battery terminals, because they can become hot and cause burns. For example, do not carry the battery in a pocket with keys or coins. • Remove the battery when the product will not be used for an extended period of time.

PCW Computer Store Hours
by JonyB 0 Comments favorite 2 Viewed Download 0 Times

Xbox Red Light Issue $79. - PS3 Yellow Light issue $99 ... IPOD REPAIR SERVICE. IPod Video and IPod classic. Parts. Labor. Total. Audio Jack. 19. 29. $ 48. Game System Repair Service Nintendo Wii -Not reading games or drive issues -Any repair without replacing parts $49 -laser replacement $69 -drive replacement $89 Xbox 360 Regular -Not reading games or drive issues - Any repair without replacing parts $49 - Laser Replacement $69 - Drive replacement $89 -3 red lights, no video, e74, or any display issue - Motherboard Repair $79 Xbox 360 Slim -Not reading games or drive issue -Any repair without replacing parts $49 -laser replacement $79 -Drive replacement – will call with price PS3 -Not reading or drive issues -Any repair without replacing parts $49 -laser replacement $99 -Drive replacement – will call with price -red light or display issues -Motherboard repair $99 Any other issue PCW Computer will Call

Your Local SEO Specialists
by LADSolutions 0 Comments favorite 15 Viewed Download 0 Times

Looking to improve your business in local search? LAD Solutions has Local SEO specialists can help you harness the power of local search and can increase your website traffic. For more info, Call 888.523.2926.

VW Amarok - Body Harness.pdf - Hayman Reese

For P/No: 04998 & 04999 only. 1. In the engine bay, disconnect the negative and positive battery terminals. 2. Remove the vehicle battery (1) by first removing any fasteners. 3. Locate the vehicle grommet behind the battery cavity area. 4. Pierce a hole in the vehicle grommet. Note: Do not connect the harness to the battery at this point. Issue Date 27-09-10 For P/No: 04997 only. 5. In the engine bay, locate the vehicle battery (1). 6. Route the body harness (2) down through to the chassis. Note: Do not connect the harness to the battery at this point. 7. Route the power input harness (1) from the engine bay down through to the chassis, following the path of the brake and fuel lines. For P/No: 04997 & 04999 only. 8. Following the diagram on the right, house the two power & ground input harness female terminals (4) into the mating connector (3). 9. Connect the power input harness connector (3) to the body harness mating connector. Issue Date 27-09-10 For P/No: 04998 only. 10. Following the diagram on the right, house the three power & ground input harness female terminals (4) into the mating connector (5). 11. Connect the power input harness connector (5) to the body harness mating connector. 12. Route the body harness (1) along the LHS chassis rail, following the path of the blue vehicle harness towards the rear of the vehicle. 13. Route the body harness (1) along the rear of the vehicle towbar towards the towbar mounting bracket. Issue Date 27-09-10

Volkswagen Amarok Brochure - CSM Transport Equipment

Volkswagen Amarok ✓ Fleet Solutions ✓ Trades and Services ✓ Recreation and 4WD ✓ Mining and Resources ✓ Government and Councils The Proven Solution...driven by you. professional canopies for Volkswagen Amarok AMAROK SINGLE CAB 1. 2. AMAROK - OPTIONAL EXTRAS Underbody Accessories Internal Fit-Out External Accessories For the full range of accessories and options, Hard Working Practicality AMAROK DUAL CAB 3. 4. Roof Rack Combinations Roof Accessories Electrical Accessories Vehicle Safety please see the Procan Product Catalogue or visit www.csmteam.com.au Customer Support and Order Hotline 1800 618 332 Standard Body Features - Volkswagen Amarok FEATURES METRO II TRADEPRO II CAMPPRO II FLEETPRO II INTEGRATED BODY ✓ ✓ ✓ ✓ SLIDE ON BODY O O O X LIFT OFF BODY X O O O 2 SIDE DOORS ONLY ✓ O ✓ O 2 SIDE DOORS + REAR DOOR O ✓ X ✓ S/S FOLDING T LATCH ✓ X X X REIGULLATCH (TURN ACTION) X ✓ X X E-ZEE LATCH (SLAM ACTION) X X ✓ ✓ CENTRAL LOCKING X O O ✓ DOOR ALERT X O O ✓ FRONT WINDOW O O O O REAR WINDOW O O O O SIDE WINDOW X O O O TAIL LIGHT CHANNEL X X ✓ ✓ TAIL LIGHT BRACKETS ✓ ✓ X X 1 PIECE MUDGUARDS X X ✓ ✓ 4 SINGLE MUDGUARDS ✓ ✓ X X 2 INTERNAL ROOF LIGHTS (LED) X O O ✓ O O O 1650/1800 1650/1800 1650/1800 BODY LENGTH – EXTRA CAB N/A N/A N/A N/A BODY LENGTH – SINGLE CAB 2400 2400 2250/2400 2250/2400 BODY WIDTH – ALL CABS 1875 1875 1875/1925 1875/1925 BODY HEIGHT 1000 1000 1000 1000 ✓ = STANDARD SUPPLY O = OPTIONAL SUPPLY X = NOT AVAILABLE Hard working practicality Freecall: 1800 618 332 Sales: +61 7 3868 4453 Nexus 45, 45 Navigator Place, Hendra, QLD 4011 Production: +61 7 4667 1844 481 - 483 East Street, Warwick, QLD 4370 Email: sales@csmteam.com.au www.csmteam.com.au Please note, images may show options and accessories that are not standard supply. X 1800 BODY LENGTH – DUAL CAB 8215 - Edge Marketing - www.edgeonline.com.au INTERNAL DOOR LIGHTS (LED)

SEAS - INSTRUCTIONS - RENAULT - - Avto-focus.com

- RENAULT Please read the complete document before starting the installation Brand assignment SEAS add-on module is delivered NOT PROGRAMMED, therefore a brand (Renault in this case) must be set with computer and specific program SETUP TRUCK This procedure can be achieved both before and after the installation on the vehicle (if after the installation, the vehicle power batteries must be disconnected during the operations). • Connect the programming cable to the USB port of your PC • Connect the programming cable to the SEAS module by using the white 4 pins connector; during this operation the LED (Light Emission Diode) of the SEAS module will be off. • Run the program SimulaCan (select it from the list of programs installed on your pc). • Proceed as follow: Select “Start” Wait for next screen displayed (the time required can vary according to the quantity of virtual COM installed) Renault_eng.doc Pagina 1 di 5 Ver. 0.1 If the connection is successfully achieved (serial communication recognized and accepted) the program will display this page: you can now select RENAULT brand Select “Send PROG” When the programming operation is completed, the yellow LED on your SEAS module will turn on. Select “Quit” to close the program SimulaCan • Disconnect the programming cable of your SEAS module and place the specific cover on top of the white 4 pins connector. IMPORTANT: the following instructions indicate how to connect and install your SEAS module on the original AdBlue system of the truck. The number displayed and the colour of the conductors of the AdBlue system are referred to Renault Premium 450 year 2008, these details may vary according to different production lots or vehicle equipment. Please refer to the schemes/layouts supplied with the Renault technical manual to identify the CAN-Bus line of the AdBlue system, its protection fuse and the power feeding. The main working procedure of SEAS modules does not vary.

Gateway Lite BT install guide - Dension

Gateway Lite BT enables music playback from a USB storage or iPod through your vehicle’s entertainment system, using the buttons of the car stereo for basic control. Once the head unit has been removed, disconnect the antenna cable (1) and then unclip the main wiring connector from the head unit (2). This will differ in all makes and manufacturers. This device also offers handsfree mobile call handling via the original buttons of the Head Unit (Radio). Connect the 12 way micro-fit (12 pin molex) to the Car side of the Gateway Lite BT module. The Dension Gateway Lite BT is available in specific versions for different vehicle types, therefore the exact operation and installation may be different in each case. Warning! Do not trap the cables, or leave them in a position where they may become trapped after refitting the head unit. Ensure the device is correctly fitted before running the cable. Then, reconnect the Dension supplied main radio connector to the rear of the head unit. Gateway Lite BT is designed to give easy to manage control, in cars where it is not possible to display text, therefore only basic control is available (track skip functions and USB folder browsing). At first please make sure that the vehicle compatibility is correct. Connect the round iPod connector and USB to the module and feed them through the dashboard to an appropriate location. With the main radio cable removed, first connect the Dension supplied cable to the original factory cable harness.

955.421.020.99.CSB
by Maradoni 0 Comments favorite 6 Viewed Download 0 Times

These instructions only apply to this particular version center support bearing and may not be correct for other versions. TOOLS NEEDED: • Ratchet • 12mm serrated wrench (triple square bit) – NAPA # SER2306 • 13mm socket • 18mm socket • 6 inch extension • 18mm open end wrench • Rubber mallet or dead blow hammer. . Expanding flat nosed snap ring pliers . Various other common hand tools INSTRUCTIONS: Read these entirely and understand them BEFORE you attempt this procedure. 1. Apply parking brake and wheel chocks to prevent vehicle from rolling. A lift is recommended for this repair. IMPORTANT: Carefully mark driveshaft orientation on both ends of shaft sections. (Transmission and differential ends, as well as splined ends where the two drive shafts come apart to allow removal of center support) The sections MUST be reassembled EXACTLY as they came apart for the removal of the old center support bearing, and the driveshaft needs to be reinstalled EXACTLY the same way, in the exact same orientation. Failure to do so can result in imbalance, vibration, and potential damage to vehicle. Otherwise a professional drive shaft shop must be employed to re-balance entire assembly. 2. Remove 6 10mm bolts at joint at rear of back driveshaft. Use the M12 triple square (12point) tool. (NAPA part number SER2306). 3. Remove 3 18mm wrench size (12mm bolt size) bolts from front of driveshaft. 4. Remove 3 18mm wrench size (12mm bolt size) bolts on flex disc. 5. Remove 13mm wrench size (8mm bolt size) bolts on plate covering center support. 6. On some models (Turbos), it may be necessary to loosen various exhaust system clamps, hangers and components to ease access to driveshaft. 7. Pull driveshaft toward front of vehicle to separate it from differential.

« previous  123456789