Found 749 related files. Current in page 1
BORA-CARE’s patented formula penetrates deep into the wood providing long lasting protection and termite control against subterranean termites, drywood termites, Formosan termites, wood destroying beetles and decay fungi. This Natural Termite Control product comes from Nisus - The World’s Leader in Borate Technology.
Buy affordable home in Gaur Sorts wood Sector 79 Noida with Buniyad Real Estate Services and get best offers on the same. Gaur Sports wood offers luxurious 3 & 4 bhk apartments in sector 79, Noida.
Hydrofire is an Intelligent Heating Solution company based in Cape Town, South Africa. We offer Unique Heating Solutions Wood burning fireplaces stoves where by a single fireplace can be used to heat an entire home.
ROTATING ENGINE STANDS 1. Overall visually inspect stand for any signs of wear and fatigue. 2. Lubricate spindles and gear box as referenced in vendor literature if equipped. 3. Inspect anti-rotation locking mechanism if equipped. 4. Install weight equal to engine weight to the engine stand for approximately 2 min. 5. Rotate weight set 360º in both directions if equipped. Operation should be free of binding and/or catching during rotation. 6. Dismantle fixture and visually inspect stand for any signs of wear or failure. Any item, which does not successfully pass the test, is to be rejected and discarded or returned to Tronair for evaluation. Load Cell Data Load Cell Display Cylinder/Pump Eyebolt 2x4 Wood Block Install Weight To Stand 08-2030-0000 AND 08-2034-0000 1. Install engine stand test fixture. 2. Position beam assembly in the center of the engine stand. 3. Tighten beam locks evenly, until the beam assembly is locked in place. 4. Position engine stand over eye hook in floor. Line eye hook directly under pull point of the test fixture. 5. Install 2 x 4 inch block under wheels and lock stand in place. 6. Attach load cell, pull cylinder to eyebolt. 7. Put engine stand through two cycles of loading the engine stand to 3,000 pounds (2,667 psi on gauge). Hold for 30 seconds then release load. 8. Inspect all welds and joints for signs of distortion; if no defects are found, the engine stand is good. 9. If defects are found discard or return to Tronair for evaluation.
A.S.M.E. Construction: Built in accordance with the ASME Code, ensures design integrity for long life. Ensures safety and reliability with third party inspection of standards compliance. Underwriters Package Label [UL/cUL]: Ensures the complete package [burner/boiler] has been tested and certified to the UL standards of safety and controls requirements. High Turndown Burner: For standard emissions [uncontrolled], up to 10:1 turndown on Gas firing, reduces inefficient on/off operation, reducing fuel consumption. Boiler stays on line during low load conditions for optimum efficiency and performance. Airfoil damper design eliminates low fire excess air spikes, increasing combustion efficiency. Boiler/burner by single manufacturer eliminating divided responsibility. Hinged Burner Design: Standard for all sizes of the Elite series and sizes 400 and greater on the Premium series, optional for Premium series sizes 350 and less. Burner assembly is attached to the front boiler wall with integral hinges, permits burner swing out for ease of service, maintenance, and inspection. Swedge-Fitted Tube Attachment: Eliminates welded tube attachment to each drum providing ease of tube replacement. Eliminates rolling or welding of tube replacement, reduces maintenance costs. Thermal Stress Protection: 25 Year Thermal Shock Warranty ensures tube integrity against thermal stress, associated with hydronic heating systems. Bent tube design provides ability to withstand thermal stress of tubes during rapid load swings and cold water returns.
Keep handles dry, clean, and free from oil and grease. Do not use chain saw for purposes not intended. For example: do not use chain saw for cutting plastic, masonry or non-wood building materials. Use of the chain saw for operations different than intended could result in a hazardous situation. 13. Causes and operator prevention of kickback: Kickback may occur when the nose or tip of the guide bar touches an object, or when the wood closes in and pinches the saw chain in the cut. Tip contact in some cases may cause a sudden reverse reaction, kicking the guide bar up and back towards the operator. Pinching the saw chain along the top of the guide bar may push the guide bar rapidly back towards the operator. Either of these reactions may cause you to lose control of the saw which could result in serious personal injury. Do not rely exclusively upon the safety devices built into your saw. As a chain saw user, you should take several steps to keep your cutting jobs free from accident or injury. Kickback is the result of tool misuse and/or incorrect operating procedures or conditions and can be avoided by taking proper precautions as given below: - Maintain a firm grip, with thumbs and fingers encircling the chain saw handles, with both hands on the saw and position your body and arm to allow you to resist kickback forces. Kickback forces can be controlled by the operator, if proper precautions are taken. 1) - Do not overreach and do not cut above shoulder height.
FEATURES: Attractive 3 and 4 Bedroom Homes Beautiful Decorative Door Attractive Lighting w /Ceiling Fans Family Room Nook Dining Room Master Bedroom w/ walk in closets Two/Three Additional Bedrooms Master Bath & Full Bathroom Spacious Energy Efficient Kitchen w/ Granite Countertops Refrigerator w/ Ice Maker Dishwasher Flat Top Range Washer/Dryer Ceramic Tile Floors Wood Laminate Floors Central Heat & Air Pre-Wired for Cable Activated Security System Irrigation System Covered LanaiLarge Backyard 4230-4250 HARBOR VIEW PLACE For Sale! Asking Prices are in the Lower $100.000’s CALL TODAY! OUR HOUSING COUNSELOR WILL GUIDE YOU THROUGH THE PROGRAM AND PREPARE YOU FOR THE RESPONSIBILITY OF HOMEOWNERSHIP. 904-358-1224 *Subsidy amount may vary ** For more information visit our website 3105 N. Main Street Jacksonville, FL 32206 Office: 904-358-1224 Get A $250 Visa Card for every home buyer you refer that closes w/ Metro North CDC www.MetroNorthCDC.com Metro North’s Harbor View Place You May Receive Up To $40,000 In Down Payment Assistance* FEATURES: Attractive 3 and 4 Bedroom Homes Beautiful Decorative Door Attractive Lighting w /Ceiling Fans Family Room Nook Dining Room Master Bedroom w/ walk in closets Two/Three Additional Bedrooms Master Bath & Full Bathroom Spacious Energy Efficient Kitchen w/ Granite Countertops Refrigerator w/ Ice Maker Dishwasher Flat Top Range Washer/Dryer Ceramic Tile Floors Wood Laminate Floors Central Heat & Air Pre-Wired for Cable Activated Security System Irrigation System Covered LanaiLarge Backyard 4230-4250 HARBOR VIEW PLACE For Sale! Asking Prices are in the Lower $100.000’s CALL TODAY! OUR HOUSING COUNSELOR WILL GUIDE YOU THROUGH THE PROGRAM AND PREPARE YOU FOR THE RESPONSIBILITY OF HOMEOWNERSHIP. 904-358-1224 *Subsidy amount may vary ** For more information visit our website Get A $250 Visa Card for every home buyer you refer that closes w/ Metro North CDC 3105 N. Main Street Jacksonville, FL 32206 Office: 904-358-1224 www.MetroNorthCDC.com
Avalon Rose Wood is 2/3BHK affordable and luxuries residential project in Bhiwadi released by The Avalon Group.For more information and site visit call at +91-9999268444.