SEARCH

Found 1677 related files. Current in page 1

99 dodge durango dash removal

520 CRF 150R and 625 KX 450F 06-08 Flywheel ... - Steahly Offroad

Installation Instructions for CRF 150R and KX450F Steahly Flywheel Weight Warning: Improper instalation of this flywheel weight could result in engine damage or a serious crash. If you do not have the tools or the mechanical abilities take it to a professional. 1. Drain the engine oil or turn off the gas and lay the bike on its side. 2. Remove the shift lever. 3. Remove the ignition cover. Take care not to tear the gasket or have a new gasket on hand. Be carefull that you don’t lose the two dowel pins that are between the cover and the engine case. 4. Remove the flywheel nut. Use an air impact wrench or figure out a way to keep the flywheel from rotating while you remove the nut. A strap wrench or an automotive oil filter wrench may work as a holding tool or try putting the bike in high gear and holding the rear brake on. 5. Pull off the stock flywheel with the proper flywheel puller that has a crank end protection cap. Steahly part number E-63. Do not attempt removal with out the correct puller. Do not use claw type pullers. 6. Fit the flywheel weight on to the stock flywheel. Line up the two threaded holes in the weight with two holes in the stock flywheel. 7. Clean the threads of the two special bolts with contact cleaner. Put a big drop of red Loctite or other high strength thread locker on the threads of the 2 bolts. Install the two special bolts as shown in the picture and torque to 12 foot pounds. 8. Unless you plan to take the weight on and off a lot we highly recommend using a center punch and a hammer to flare out the threads at the end of the bolt (see pictures below). This will reduce the possibility of the bolt coming loose. 9. Clean up the flywheel and weight and remove any metal stuck to the magnets. 10. Install the flywheel with weight back onto the tapered crank shaft end making sure the key ways are lined up. Torque the stock nut to 42 ft- lbs.

Eaton Heavy-Duty Clutches CLSM0200 - Roadranger

The major cause of clutch failure is excessive heat. Excessive heat generated between the flywheel, driven discs, intermediate plate and pressure plate can cause the metal to flow and the material to be destroyed. If this occurs, the clutch can burst which can cause property damage, serious bodily injury or death. In order to prevent clutch failure resulting from excessive heat: 1. Do not exceed recommended vehicle loads. 2. The clutch should only be used for the recommended applications. 3. Drivers should be properly trained in starting, shifting and operation of the clutch. 4. Drivers should report erratic clutch operation as soon as possible to permit maintenance personnel to inspect, adjust or lubricate as required. 5. The removal and installation procedure described for each component may vary for your vehicle. For Solo and Heavy-Duty ECA clutches only, install shipping bolts before removing clutch assembly from the flywheel. IMPORTANT For service information and assistance, call the Roadranger Help Desk at 1-800-826-HELP (4357) (Mexico: 01-800-826HELP (4357). You may also find more information about Eaton Clutches at www.Roadranger.com. Mechanics must be familiar with proper clutch adjustment, linkage adjustment, lubrication and other maintenance troubleshooting procedures outlined in the Failure Analysis Guide. Every effort has been made to ensure the accuracy of the information contained in this manual. However, Eaton Corporation makes no warranty, expressed or implied, based on the information provided.

1.9 CRANKSHAFT ASSEMBLY - DDCSN
by Prezta 0 Comments favorite 6 Viewed Download 0 Times

The crankshaft is precision-forged with seven main bearings and eight custom-forged counter weights, and a vibration damper at the front end. For an exploded view of the crankshaft, main bearings, and main bearing caps, see Figure 1-42. 1. Crankshaft 5. Lower Bearing Shell (center) 2. Upper Bearing Shell(s) 6. Main Bearing Cap(s) 3. Upper Bearing Shell (center) 7. Main Bearing Cap (center) 4. Lower Bearing Shell(s) 8. Main Bearing Cap Bolt Figure 1-42 Crankshaft, Main Bearings, and Main Bearing Caps All information subject to change without notice. (Rev. 3/04) 6SE412 0403 Copyright © 2006 DETROIT DIESEL CORPORATION From Bulletin 1–MBE4000–06 1-57 1.9 CRANKSHAFT ASSEMBLY 1.9.1 Crankshaft Removal Remove the crankshaft as follows: FALLING ENGINE To avoid injury from a falling engine, an adequate lifting device with a spreader bar and sling should be used to lift the engine. The sling and spreader bar should be adjusted so the lifting hooks are vertical to prevent bending the lifter brackets. To ensure proper weight distribution, all provided lifter brackets must be used. NOTICE: A spreader bar must be used at all times in conjunction with the front and rear lifter brackets to lift the EGR engine to ensure that no engine damage will result. The brackets are designed to lift vertically. 1. Remove the engine from the vehicle.

eCA913 Renault RS Megane.qxp - Injen
by Corsa 0 Comments favorite 2 Viewed Download 0 Times

Congratulations! You have just purchased the best engineered, dyno-proven cold air intake system available. Please check the contents of this box immediately. Report any defective or missing parts to the Authorized Injen Technology dealer you purchased this product from. Before installing any parts of this system, please read the instructions thoroughly. If you have any questions regarding installation please contact the dealer you purchased this product from. Installation DOES require some mechanical skills. A qualified mechanic is always recommended. *Do not attempt to install the intake system while the engine is hot. The installation may require removal of radiator fluid line that may be hot. Injen Technology offers a limited lifetime warranty to the original purchaser against defects in materials and workmanship. Warranty claims must be handled through the dealer from which the item was purchased. Injen Technology 285 Pioneer Place Pomona, CA 91768 USA Please check the contents of this box immediately. Note: This intake system was Dyno-tested with an Injen filter and Injen parts. The use of any other filter or part will void the warranty and CARB exemption number.

Drive Shaft & Transfer Case Diagnosis Service & Repair

Troubleshoot common drive shaft problems. ○ Check ... Remove and replace a drive shaft assembly. ○ Replace ... Drive Shaft Vibration can be caused by. Learning Objectives Troubleshoot common drive shaft problems. Check universal joint wear. Measure drive shaft runout. Remove and replace a drive shaft assembly. Replace universal joints. Perform basic service operations on a transfer case. Cite and practice good safety procedures. Chapter 60 1. Because a Transfer Case is heavy, use a transmission jack when removing. 2. Before disassembling a Universal Joint, Joint scribe/mark each component. Transfer Case Removal Use a hoist and transmission jack Transfer Case Oil Check the oil condition and level first. Replace dirty or contaminated oil

955.421.020.99.CSB
by Maradoni 0 Comments favorite 5 Viewed Download 0 Times

These instructions only apply to this particular version center support bearing and may not be correct for other versions. TOOLS NEEDED: • Ratchet • 12mm serrated wrench (triple square bit) – NAPA # SER2306 • 13mm socket • 18mm socket • 6 inch extension • 18mm open end wrench • Rubber mallet or dead blow hammer. . Expanding flat nosed snap ring pliers . Various other common hand tools INSTRUCTIONS: Read these entirely and understand them BEFORE you attempt this procedure. 1. Apply parking brake and wheel chocks to prevent vehicle from rolling. A lift is recommended for this repair. IMPORTANT: Carefully mark driveshaft orientation on both ends of shaft sections. (Transmission and differential ends, as well as splined ends where the two drive shafts come apart to allow removal of center support) The sections MUST be reassembled EXACTLY as they came apart for the removal of the old center support bearing, and the driveshaft needs to be reinstalled EXACTLY the same way, in the exact same orientation. Failure to do so can result in imbalance, vibration, and potential damage to vehicle. Otherwise a professional drive shaft shop must be employed to re-balance entire assembly. 2. Remove 6 10mm bolts at joint at rear of back driveshaft. Use the M12 triple square (12point) tool. (NAPA part number SER2306). 3. Remove 3 18mm wrench size (12mm bolt size) bolts from front of driveshaft. 4. Remove 3 18mm wrench size (12mm bolt size) bolts on flex disc. 5. Remove 13mm wrench size (8mm bolt size) bolts on plate covering center support. 6. On some models (Turbos), it may be necessary to loosen various exhaust system clamps, hangers and components to ease access to driveshaft. 7. Pull driveshaft toward front of vehicle to separate it from differential.

STEERING COLUMN Article Text - LIL EVO

The steering system consists of solid steering shaft with a lower joint assembly. Stealth and 3000GT models are equipped with a Supplemental Restraint System (SRS) that includes an air bag and clockspring located in the steering column. WARNING: On Stealth and 3000GT, before doing any repairs, disconnect and shield battery ground. Disconnect SRS connector at control unit. Use caution when working around steering column (air bag could deploy). TROUBLE SHOOTING Refer to TROUBLE SHOOTING - BASIC PROCEDURES article in the GENERAL TROUBLE SHOOTING section. REMOVAL & INSTALLATION STEERING WHEEL & HORN PAD R & I Removal (All Models Except Stealth & 3000GT) 1) Remove horn pad. On Galant, push horn pad toward top of steering wheel for removal. On Precis, push and turn horn pad assembly to remove and disconnect horn button connector. On all other models, remove screws and/or pry horn pad from steering wheel. 2) On all models, place reference mark on steering wheel and steering column shaft for reassembly reference. Remove steering wheel retaining nut and washer. Using steering wheel puller, remove steering wheel. CAUTION: DO NOT hammer on steering wheel during removal, as it may damage steering column. Installation To install, reverse removal procedure. Ensure reference marks are aligned. Tighten steering wheel retaining nut to specification. See TORQUE SPECIFICATIONS table at end of article. Removal (Stealth & 3000GT) 1) Set front wheels in the straight-ahead position. Remove STEERING COLUMN

TRANSMISSION REMOVAL & INSTALLATION - A/T ... - LIL EVO

AUTOMATIC FWD MODELS REMOVAL 1) Remove battery and battery tray. On 3000GT, remove undercover(s). On Eclipse turbo, drain and remove intercooler. On all models, remove air cleaner and case. Raise and support vehicle. Remove wheels. Disconnect control cables at transaxle. Drain transaxle fluid. 2) On Mirage 1.6L, disconnect tension rod. On all models, disconnect neutral safety switch connector, oil cooler hoses and electrical connectors from transaxle. Disconnect speedometer cable and throttle control cable (if equipped). Remove starter motor. 3) On Galant models with electronically controlled suspension, remove air compressor and bracket. Disconnect front height sensor rod at lower control arm. 4) On all models, remove upper transaxle-to-engine bolts. Remove engine undercover (if equipped). On all models, remove drive axle shafts. See FWD AXLE SHAFTS article in DRIVE AXLES. Separate lower control arms from struts for access to axle shafts (if necessary). 5) Remove front exhaust pipe (if necessary). On Eclipse 4WD, Galant 4WD and 3000GT, remove right member and gusset. On 4WD models, separate transfer assembly from transaxle. Reference mark transfer assembly-to-drive shaft and remove transfer assembly. 6) On all models, remove transmission inspection (dust) cover. Place index mark on torque converter and drive plate for reassembly reference. Remove torque converter-to-drive plate bolts. Push torque converter away from engine into transaxle. 7) Support transaxle with jack. Remove transaxle mounts bolts, mounting brackets and remaining transaxle-to-engine bolts. Slide transaxle assembly to right and lower to remove. CAUTION: Ensure torque converter is fully seated in transaxle before installation. Always install new snap rings on inner constant velocity joints.

AWD Trans Service Manual - 3000GT/Stealth International

3000GT/Stealth International, an owners and enthusiast group focused on the Mitsubishi. 3000GT, Dodge Stealth and Mitsubishi GTO. Great care has been 3000GT/Stealth International, an owners and enthusiast group focused on the Mitsubishi. 3000GT, Dodge Stealth and Mitsubishi GTO. Great care has been 3000GT/Stealth International, an owners and enthusiast group focused on the Mitsubishi. 3000GT, Dodge Stealth and Mitsubishi GTO. Great care has been 3000GT/Stealth International, an owners and enthusiast group focused on the Mitsubishi. 3000GT, Dodge Stealth and Mitsubishi GTO. Great care has been 3000GT/Stealth International, an owners and enthusiast group focused on the Mitsubishi. 3000GT, Dodge Stealth and Mitsubishi GTO. Great care has been 3000GT/Stealth International, an owners and enthusiast group focused on the Mitsubishi. 3000GT, Dodge Stealth and Mitsubishi GTO. Great care has been 3000GT/Stealth International, an owners and enthusiast group focused on the Mitsubishi. 3000GT, Dodge Stealth and Mitsubishi GTO. Great care has been 3000GT/Stealth International, an owners and enthusiast group focused on the Mitsubishi. 3000GT, Dodge Stealth and Mitsubishi GTO. Great care has been 3000GT/Stealth International, an owners and enthusiast group focused on the Mitsubishi. 3000GT, Dodge Stealth and Mitsubishi GTO. Great care has been 3000GT/Stealth International, an owners and enthusiast group focused on the Mitsubishi. 3000GT, Dodge Stealth and Mitsubishi GTO. Great care has been ...

Installation Instructions - CatalogRack.com

70-7003/70-7004 Amplifier Integration Harness Amplifier Integration Harness 1994-96 Dodge Stealth 1995-98 Eagle Talon 1994-99 Mitsubishi 3000GT 1994-04 Mitsubishi Diamante 1995-05 Mitsubishi Eclipse 1994-03 Mitsubishi Galant 2002-07 Mitsubishi Lancer 1997-02 Mitsubishi Mirage 1997-05 Mitsubishi Montero 2003-06 Mitsubishi Outlander To integrate an aftermarket head unit with the factory Infinity amplifier. Or To integrate an aftermarket amplifier with the factory Infinity head unit. AUDIO HARNESS POWER HARNESS 1994-96 Dodge Stealth 1995-98 Eagle Talon 1994-99 Mitsubishi 3000GT 1994-04 Mitsubishi Diamante 1995-05 Mitsubishi Eclipse 1994-03 Mitsubishi Galant 2002-07 Mitsubishi Lancer 1997-02 Mitsubishi Mirage 1997-05 Mitsubishi Montero 2003-06 Mitsubishi Outlander To integrate an aftermarket head unit with the factory Infinity amplifier. Or To integrate an aftermarket amplifier with the factory Infinity head unit. AUDIO HARNESS POWER HARNESS 1-800-221-0932 www.metraonline.com © COPYRIGHT 2001-2009 METRA ELECTRONICS CORP. 1-800-221-0932 www.metraonline.com © COPYRIGHT 2001-2009 METRA ELECTRONICS CORP. 70-7003/70-7004 INSTALLATION INSTRUCTIONS 70-7003/70-7004 INSTALLATION INSTRUCTIONS Amplifier Integration Harness Amplifier Integration Harness 1994-96 Dodge Stealth 1995-98 Eagle Talon 1994-99 Mitsubishi 3000GT 1994-04 Mitsubishi Diamante 1995-05 Mitsubishi Eclipse 1994-03 Mitsubishi Galant 2002-07 Mitsubishi Lancer 1997-02 Mitsubishi Mirage 1997-05 Mitsubishi Montero 2003-06 Mitsubishi Outlander To integrate an aftermarket head unit with the factory Infinity amplifier. Or To integrate an aftermarket amplifier with the factory Infinity head unit. AUDIO HARNESS POWER HARNESS 1-800-221-0932 www.metraonline.com © COPYRIGHT 2001-2009 METRA ELECTRONICS CORP. 1994-96 Dodge Stealth 1995-98 Eagle Talon 1994-99 Mitsubishi 3000GT 1994-04 Mitsubishi Diamante 1995-05 Mitsubishi Eclipse 1994-03 Mitsubishi Galant 2002-07 Mitsubishi Lancer 1997-02 Mitsubishi Mirage 1997-05 Mitsubishi Montero 2003-06 Mitsubishi Outlander To integrate an aftermarket head unit with the factory Infinity amplifier. Or To integrate an aftermarket amplifier with the factory Infinity head unit. AUDIO HARNESS POWER HARNESS 1-800-221-0932 www.metraonline.com © COPYRIGHT 2001-2009 METRA ELECTRONICS CORP. To Integrate Aftermarket Head Unit with Factory Amplifier To Integrate Aftermarket Head Unit with Factory Amplifier AUDIO HARNESS AUDIO HARNESS Connect the RCA cables to the line outputs on the aftermarket head unit OR use Metra’s #FL-LOC605 (sold separately) Line Output Converters to supply line outputs. FUNCTION COLOR Right Front Gray Left Front White Right Rear Purple Left Rear Green Amplifier Turn On Blue/White POWER HARNESS Connect the power wires to the aftermarket head unit. FUNCTION COLOR Ground To vehicle chassis Battery/Memory Yellow Ignition/Accy Red Power Antenna Blue Illumination Orange (If the aftermarket head unit does not have an Illumination wire, do not connect the orange wire, and cap this wire to prevent a short circuit.) NOTE: If the system has noise, use Metra’s #FL-GL605(sold separately) Ground Loop Isolator to remove the noise. Connect the RCA cables to the line outputs on the aftermarket head unit OR use Metra’s #FL-LOC605 (sold separately) Line Output Converters to supply line outputs. FUNCTION COLOR Right Front Gray Left Front White Right Rear Purple Left Rear Green Amplifier Turn On Blue/White POWER HARNESS Connect the power wires to the aftermarket head unit. FUNCTION COLOR Ground To vehicle chassis Battery/Memory Yellow Ignition/Accy Red Power Antenna Blue Illumination Orange (If the aftermarket head unit does not have an Illumination wire, do not connect the orange wire, and cap this wire to prevent a short circuit.) NOTE: If the system has noise, use Metra’s #FL-GL605(sold separately) Ground Loop Isolator to remove the noise.

« previous  123456789