Found 2649 related files. Current in page 1
For P/No: 04998 & 04999 only. 1. In the engine bay, disconnect the negative and positive battery terminals. 2. Remove the vehicle battery (1) by first removing any fasteners. 3. Locate the vehicle grommet behind the battery cavity area. 4. Pierce a hole in the vehicle grommet. Note: Do not connect the harness to the battery at this point. Issue Date 27-09-10 For P/No: 04997 only. 5. In the engine bay, locate the vehicle battery (1). 6. Route the body harness (2) down through to the chassis. Note: Do not connect the harness to the battery at this point. 7. Route the power input harness (1) from the engine bay down through to the chassis, following the path of the brake and fuel lines. For P/No: 04997 & 04999 only. 8. Following the diagram on the right, house the two power & ground input harness female terminals (4) into the mating connector (3). 9. Connect the power input harness connector (3) to the body harness mating connector. Issue Date 27-09-10 For P/No: 04998 only. 10. Following the diagram on the right, house the three power & ground input harness female terminals (4) into the mating connector (5). 11. Connect the power input harness connector (5) to the body harness mating connector. 12. Route the body harness (1) along the LHS chassis rail, following the path of the blue vehicle harness towards the rear of the vehicle. 13. Route the body harness (1) along the rear of the vehicle towbar towards the towbar mounting bracket. Issue Date 27-09-10
Australian Competition and Consumer Commission 23 Marcus Clarke Street, Canberra, Australian Capital Territory, 2601 © Commonwealth of Australia 2013 This work is copyright. In addition to any use permitted under the Copyright Act 1968, all material contained within this work is provided under a Creative Commons Attribution 3.0 Australia licence, with the exception of: • the Commonwealth Coat of Arms • the ACCC and AER logos • any illustration, diagram, photograph or graphic over which the Australian Competition and Consumer Commission does not hold copyright, but which may be part of or contained within this publication. The details of the relevant license conditions are available on the Creative Commons website, as is the full legal code for the CC BY 3.0 AU licence. Requests and inquiries concerning reproduction and rights should be addressed to the Director, Internal Communication and Publishing Services, ACCC, GPO Box 3131, Canberra ACT 2601, or firstname.lastname@example.org. Important notice The information in this publication is for general guidance only. It does not constitute legal or other professional advice, and should not be relied on as a statement of the law in any jurisdiction. Because it is intended only as a general guide, it may contain generalisations.
- RENAULT Please read the complete document before starting the installation Brand assignment SEAS add-on module is delivered NOT PROGRAMMED, therefore a brand (Renault in this case) must be set with computer and specific program SETUP TRUCK This procedure can be achieved both before and after the installation on the vehicle (if after the installation, the vehicle power batteries must be disconnected during the operations). • Connect the programming cable to the USB port of your PC • Connect the programming cable to the SEAS module by using the white 4 pins connector; during this operation the LED (Light Emission Diode) of the SEAS module will be off. • Run the program SimulaCan (select it from the list of programs installed on your pc). • Proceed as follow: Select “Start” Wait for next screen displayed (the time required can vary according to the quantity of virtual COM installed) Renault_eng.doc Pagina 1 di 5 Ver. 0.1 If the connection is successfully achieved (serial communication recognized and accepted) the program will display this page: you can now select RENAULT brand Select “Send PROG” When the programming operation is completed, the yellow LED on your SEAS module will turn on. Select “Quit” to close the program SimulaCan • Disconnect the programming cable of your SEAS module and place the specific cover on top of the white 4 pins connector. IMPORTANT: the following instructions indicate how to connect and install your SEAS module on the original AdBlue system of the truck. The number displayed and the colour of the conductors of the AdBlue system are referred to Renault Premium 450 year 2008, these details may vary according to different production lots or vehicle equipment. Please refer to the schemes/layouts supplied with the Renault technical manual to identify the CAN-Bus line of the AdBlue system, its protection fuse and the power feeding. The main working procedure of SEAS modules does not vary.
The information in this document is subject to change without notice. Neither Hewlett-Packard ® Company nor Apple Computer, Inc. make any warranties of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Neither HP or Apple shall be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material. THE WARRANTY TERMS CONTAINED IN THIS STATEMENT, EXCEPT TO THE EXTENT LAWFULLY PERMITTED, DO NOT EXCLUDE, RESTRICT OR MODIFY AND ARE IN ADDITION TO ANY MANDATORY STATUTORY RIGHTS APPLICABLE TO THE SALE OF THIS PRODUCT OR SERVICE TO YOU. HP assumes no responsibility for the use or reliability of its software on equipment that is not furnished by HP. This document contains proprietary information that is protected by copyright. All rights are reserved. No part of this document may be photocopied, reproduced, or translated to another language without the prior written consent of HP. Hewlett-Packard Company P.O. Box 4010 Cupertino, CA 95015-4010 USA © 2005 Hewlett-Packard Development Company, L.P. All rights reserved. Apple, the Apple logo, FireWire, iPod, iTunes, Mac, Macintosh, and Mac OS are trademarks of Apple Computer, Inc., registered in the U.S. and other countries/regions. iTunes Music Store is a service mark of Apple Computer, Inc., registered in the U.S. and other countries/regions. For legal or rightholderauthorized copying only. Don’t steal music.
February 2005 Supersedes J3311-DSD May 1994 Contact Information: Dana Corporation Heavy Vehicle Technologies and Systems Service P.O. Box 321 Toledo, OH 43697-0321 1-800-SAY-DANA (729-3262) Dana Corporation Heavy Vehicle Technologies and Systems Service – Canada 5095 South Service Road Beamsville, Ontario, Canada L0R 1B0 Tech Service: 1-905-563-4991 www.dana.com www2.dana.com/expert J3311-1-HVTSS 2/05 Printed in U.S.A. © Dana Corporation 2005 All rights reserved. Dana Corporation Heavy Vehicle Technologies and Systems Service – International 419-861-6325 Driveshaft Installation Safety Precautions General Safety Information WARNING: GUARDING AUXILIARY DRIVESHAFTS To prevent injury to yourself and /or damage to the equipment: • Read carefully all owners manuals, service manuals, and/or other instructions. • Always follow proper procedures and use proper tools and safety equipment. • Be sure to receive proper training. • Never work alone while under a vehicle or while repairing or maintaining equipment. • Always use proper components in applications for which they are approved. • Be sure to assemble components properly. • Never use worn-out or damaged components. • Always block any raised or moving device that may injure a person working on or under a vehicle. • Never operate the controls of the power take-off or other driven equipment from any position that could result in getting caught in the moving machinery. We strongly recommend that a power take-off and a directly mounted pump be used to eliminate the auxiliary driveshaft whenever possible. If an auxiliary driveshaft is used and remains exposed after installation, it is the responsibility of the vehicle designer and PTO installer to install a guard. WARNING: USING SET SCREWS.
Throughout this article I will address many basics of your vehicle’s steering, suspension, driveline, tires, and wheels. I did not intend this to be a “how to” manual with step by step instructions. It will simply illustrate the concepts. I’ll start with the lift and explain what it did to your steering, suspension, and driveline one aspect at a time. NOTES ABOUT THE ILLUSTRATIONS: 1) most are “spring under” leaf spring suspension, 2) non-pertinent parts are omitted for clarity, 3) many examples are exaggerated for illustration, and 4) most concepts illustrated also apply to spring over and coil/link suspensions. To cover the differences, I added a separate coil and link suspensions topic. Ready? OK, let’s get started. You lifted your Jeep and now it wanders all over the road and it vibrates too. What happened? Well, you just changed a lot of the vehicle’s geometry (probably without knowing it). Here’s a diagram of a stock Jeep and the proper angles. Your caster angle should be between 4 and 8 degrees positive. This caster angle creates an effect called mechanical trail. It’s the force that makes your wheels return to center. The caster angle shown below is close to stock. The point that the steering axis (black line) intersects the ground to the point to where the rotational axis touches the ground forms the points to measure your caster angle. You can best measure the caster angle from the top of the upper ball joint.
1 TON FOLDING ENGINE STAND Model 47304 ASSEMBLY AND OPERATING INSTRUCTIONS ® 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our Web site at http://www.harborfreight.com Copyright © 2002 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools . For technical questions and replacement parts, please call 1-800-444-3353 Specifications Engine Stand Capacity Assembled Dimensions Folded Dimensions Engine Turn Capacity Main Post Height 1 Ton (2000 Lbs.) 42” L x 36” W x 34” H 17” L x 22-1/2” W x 40” H 360 Degrees 32-1/2” Save This Manual You will need the manual for the safety warnings and precautions, assembly instructions, operating and maintenance procedures, parts list and diagram. Keep your invoice with this manual. Write the invoice number on the inside of the front cover. Keep the manual and invoice in a safe and dry place for future reference. Safety Warnings and Precautions WARNING: When using product, basic safety precautions should always be followed to reduce the risk of personal injury and damage to equipment. Read all instructions before using this product! 1. Avoid working alone. If an accident happens, an assistant can bring help. 2. Keep work area clean. Cluttered areas invite injuries. 3. Observe work area conditions. Don’t expose to rain. Keep work area well lighted. 4. Keep children away. Children must never be allowed in the work area. Do not let them near the Stand. 5. Store idle equipment. When not in use, the Stand must be stored in a dry location to inhibit rust. Always lock up tools and keep out of reach of children. 6. Dress properly. Do not wear loose clothing or jewelry as they can be caught in moving parts. Protective, electrically nonconductive clothes and nonskid footwear are recommended when working. Wear restrictive hair covering to contain long hair. 7. Use eye and ear protection. Always wear ANSI approved impact safety goggles. 8. Do not overreach. Keep proper footing and balance at all times. Do not reach over or across electrical cables or frames. 9. Maintain Stand with care. Inspect Stand, and if damaged, have it repaired by an authorized technician. SKU 47304
www.tuneyourengine.com. 1994 - 1997 Mitsubishi 3000GT VR4 ECU Diagram. Connector A. Connector B Connector C. Connector D. Pin #. Name. Signal Type. Connector B Name Injector 1 Injector 3 Injector 5 Injector 2 Injector 4 Injector 6 Power Ground Air Intake Temperature Sensor O2 Sensor # 1 (Right Bank) O2 Sensor # 2 (Left Bank) Engine Coolant Temperature Sensor Throttle Position Sensor Atmospheric Pressure Sensor Vehicle Speed Sensor Volume Air Flow Sensor Power Ground Sensor Ground Connector C Connector D Signal Type Speed Speed Speed Speed Speed Speed Ground Analog Analog Analog Analog Analog Analog Speed Analog Ground GroundConnector B Name Injector 1 Injector 3 Injector 5 Injector 2 Injector 4 Injector 6 Power Ground Air Intake Temperature Sensor O2 Sensor # 1 (Right Bank) O2 Sensor # 2 (Left Bank) Engine Coolant Temperature Sensor Throttle Position Sensor Atmospheric Pressure Sensor Vehicle Speed Sensor Volume Air Flow Sensor Power Ground Sensor Ground Connector C Connector D Signal Type Speed Speed Speed Speed Speed Speed Ground Analog Analog Analog Analog Analog Analog Speed Analog Ground GroundConnector B Name Injector 1 Injector 3 Injector 5 Injector 2 Injector 4 Injector 6 Power Ground Air Intake Temperature Sensor O2 Sensor # 1 (Right Bank) O2 Sensor # 2 (Left Bank) Engine Coolant Temperature Sensor Throttle Position Sensor Atmospheric Pressure Sensor Vehicle Speed Sensor Volume Air Flow Sensor Power Ground Sensor Ground Connector C Connector D Signal Type Speed Speed Speed Speed Speed Speed Ground Analog Analog Analog Analog Analog Analog Speed Analog Ground Ground
http://www.jackkey.com/ | The 2014 Nissan Sentra combines innovation with luxury at an economic price. Learn more about Nissan Sentra trims and visit your local Jack Key dealership to take a test drive today.
Jay Grenier enters his eighth season as the head baseball coach at Rhode Island College. He owns a career record of 337-213-1. Under his guidance, Rhode Island College posted a 21-14 overall record and an 8-6 (third place tie) in the Little East Conference in 2007.The Anchormen's 21 wins tied the 2006 edition's mark for the most wins in a season since the 1979 squad won 24 games. Grenier led the Anchormen to 21-20 overall record and an 8-6 (third place tie) mark in the Little East Conference in 2006, despite losing seven seniors from the NCAA Tournament squad in 2005. It was the Anchormen’s first winning season since 2003. RIC also made its first Eastern College Athletic Conference (ECAC) New England Baseball Championship appearance in 19 years. The Anchormen won their first round contest vs. UMass Boston before the tournament was halted due to inclement weather. In 2005, he led the Anchormen to their first-ever Little East Conference Baseball Tournament Championship and a berth in the NCAA Div. III Baseball Tournament. In the LEC tourney, the fifthseeded Anchormen swept through the tournament with a 4-0 record, defeating all of the four higher seeds along the way. RIC concluded the ’05 campaign with a 19-21 overall record and posted a 7-7 (fifth place) mark in the LEC during the regular season. During the Fall 2004 campaign, he led the Anchormen to their second consecutive Cardi's Furniture Fall Baseball Classic Championship. RIC concluded the 2004 season with a 19-16 overall record and a 6-8 (fifth place) mark in the Little East. The squad played six games versus teams who were nationally ranked at the time. They were victorious in two games, including a 10-5 win over fourth-ranked Eastern Connecticut. RIC turned the corner in 2003, improving to 20-19-1 overall and 5-9 (sixth place) in the Little East Conference from 10-25 overall and 2-12 (seventh place) in 2002.