SEARCH

Found 2920 related files. Current in page 1

2004 f150 heritage stereo wiring diagram

Installation of Flywheel - DDCSN
by Prezta 0 Comments favorite 6 Viewed Download 0 Times

[b] If clutch contact face is scored or worn, the flywheel may be refaced. [c] If clutch contact face is cracked, the flywheel must be replaced. NOTE: Do not remove more than 0.508 mm (0.020 in.) material from the flywheel. Maintain all of the radii when resurfacing. 2. Inspect the ring gear. [a] Check ring gear for excessively worn or damaged gear teeth. [b] If damaged gear teeth are detected, replace the ring gear. Refer to Section 1.15.3. 3. Inspect crankshaft and flywheel contact surface. [a] Check the butt end of the crankshaft and flywheel contact surface for fretting, brinelling, or burrs. See Figure 1-212. [b] Lightly stone the contact surface to remove any fretting, brinelling, or burrs. Figure 1-212 1.14.3 Crankshaft and Flywheel Mating Surfaces Installation of Flywheel Install the flywheel as follows: 1. Install two flywheel guide studs, J 36235, into two of the tapped holes in the crankshaft at the 3 and 9 o’clock position. 2. Attach the flywheel lifting tool and, using a chain hoist, position the flywheel in the flywheel housing. Align the flywheel bolt holes with the crankshaft bolt holes. All information subject to change without notice. (Rev. 2004) 6SE50 0403 Copyright © 2004 DETROIT DIESEL CORPORATION From Bulletin 2-50-04 1-261 1.14 FLYWHEEL NOTICE: A new scuff plate must be used whenever the flywheel is removed. Failure to replace the scuff plate may cause the flywheel bolts to loosen, even when torqued correctly. 3. Using a new scuff plate, install two bolts with International Compound #2® (or equivalent) through the plate 180 from each other. 4. Install the flywheel lock, J 36375–A. See Figure 1-195. 5. Remove the flywheel lifting tool and guide studs. 6. Apply International Compound #2® (or equivalent) to the threads and to the bolt head contact area (underside) of the remaining bolts. The bolt threads must be completely filled with International Compound #2® (or equivalent). Any excess must be wiped off. See Figure 1-213.

The torque turn specification for the flywheel to crankshaft bolts has ...

Additional service information is available in the Detroit Diesel Series 60 Service Manual, 6SE483. The next revision to this manual will include the revised information. As a convenience to holders of the Series 60 Service Manual, information in service manual format is attached. The page(s) may be inserted into the manual. NOTE: Manual insert pages are numbered for insertion into the current Series 60 Service Manual dated January 2004. Service manuals are available from authorized Detroit Diesel distributors. If this bulletin was obtained from the Internet, service manual page(s) are available by returning to the screen “SIB Index”, selecting attachment pages, and printing the page(s). Detroit Diesel®, DDC®, Series 60® and the spinning arrows design are registered trademarks of Detroit Diesel Corporation. © Copyright 2004 Detroit Diesel Corporation. All rights reserved. Printed in U.S.A.

Download PDF - The Washington Institute for Near East Policy

Both Abu Musab al-Zarqawi, who founded Jamaat al-Tawhid wa-l-Jihad ( JTWJ) in 1999 (see Table 1 for the history of ISIS names), and al-Qaeda head Usama bin Laden came of age during the Afghan jihad against the Soviet Union in the 1980s, but their respective organizations have distinct genetic material, attributable in part to their different backgrounds, leadership styles, and aims. This is the case even though the two groups formed a marriage of convenience beginning in 2004. One key difference involves the socioeconomic background of the groups’ founders. Whereas bin Laden and his cadre grew up in at least the upper middle class and had a university education, Zarqawi and those closest to him came from poorer, less educated backgrounds. Zarqawi’s criminal past and extreme views on takf ir (accusing another Muslim of heresy and thereby justifying his killing) created major friction3 and distrust with bin Laden when the two first met in Afghanistan in 1999.

VW Amarok - Body Harness.pdf - Hayman Reese

For P/No: 04998 & 04999 only. 1. In the engine bay, disconnect the negative and positive battery terminals. 2. Remove the vehicle battery (1) by first removing any fasteners. 3. Locate the vehicle grommet behind the battery cavity area. 4. Pierce a hole in the vehicle grommet. Note: Do not connect the harness to the battery at this point. Issue Date 27-09-10 For P/No: 04997 only. 5. In the engine bay, locate the vehicle battery (1). 6. Route the body harness (2) down through to the chassis. Note: Do not connect the harness to the battery at this point. 7. Route the power input harness (1) from the engine bay down through to the chassis, following the path of the brake and fuel lines. For P/No: 04997 & 04999 only. 8. Following the diagram on the right, house the two power & ground input harness female terminals (4) into the mating connector (3). 9. Connect the power input harness connector (3) to the body harness mating connector. Issue Date 27-09-10 For P/No: 04998 only. 10. Following the diagram on the right, house the three power & ground input harness female terminals (4) into the mating connector (5). 11. Connect the power input harness connector (5) to the body harness mating connector. 12. Route the body harness (1) along the LHS chassis rail, following the path of the blue vehicle harness towards the rear of the vehicle. 13. Route the body harness (1) along the rear of the vehicle towbar towards the towbar mounting bracket. Issue Date 27-09-10

Trolley Jacks - Supplier Guide - ACCC

Australian Competition and Consumer Commission 23 Marcus Clarke Street, Canberra, Australian Capital Territory, 2601 © Commonwealth of Australia 2013 This work is copyright. In addition to any use permitted under the Copyright Act 1968, all material contained within this work is provided under a Creative Commons Attribution 3.0 Australia licence, with the exception of: • the Commonwealth Coat of Arms • the ACCC and AER logos • any illustration, diagram, photograph or graphic over which the Australian Competition and Consumer Commission does not hold copyright, but which may be part of or contained within this publication. The details of the relevant license conditions are available on the Creative Commons website, as is the full legal code for the CC BY 3.0 AU licence. Requests and inquiries concerning reproduction and rights should be addressed to the Director, Internal Communication and Publishing Services, ACCC, GPO Box 3131, Canberra ACT 2601, or publishing.unit@accc.gov.au. Important notice The information in this publication is for general guidance only. It does not constitute legal or other professional advice, and should not be relied on as a statement of the law in any jurisdiction. Because it is intended only as a general guide, it may contain generalisations.

Gateway Lite BT install guide - Dension

Gateway Lite BT enables music playback from a USB storage or iPod through your vehicle’s entertainment system, using the buttons of the car stereo for basic control. Once the head unit has been removed, disconnect the antenna cable (1) and then unclip the main wiring connector from the head unit (2). This will differ in all makes and manufacturers. This device also offers handsfree mobile call handling via the original buttons of the Head Unit (Radio). Connect the 12 way micro-fit (12 pin molex) to the Car side of the Gateway Lite BT module. The Dension Gateway Lite BT is available in specific versions for different vehicle types, therefore the exact operation and installation may be different in each case. Warning! Do not trap the cables, or leave them in a position where they may become trapped after refitting the head unit. Ensure the device is correctly fitted before running the cable. Then, reconnect the Dension supplied main radio connector to the rear of the head unit. Gateway Lite BT is designed to give easy to manage control, in cars where it is not possible to display text, therefore only basic control is available (track skip functions and USB folder browsing). At first please make sure that the vehicle compatibility is correct. Connect the round iPod connector and USB to the module and feed them through the dashboard to an appropriate location. With the main radio cable removed, first connect the Dension supplied cable to the original factory cable harness.

Rockbox user manual - Parent Directory

The Rockbox Manual for. Ipod Nano 2nd generation ... Rockbox and this manual is the collaborative effort of the Rockbox team and its contributors. See the ... The Rockbox Manual for Ipod Nano 2nd generation rockbox.org July 22, 2014 2 Rockbox http://www.rockbox.org/ Open Source Jukebox Firmware Rockbox and this manual is the collaborative effort of the Rockbox team and its contributors. See the appendix for a complete list of contributors. c 2003-2013 The Rockbox Team and its contributors, c 2004 Christi Alice Scarborough, c 2003 José Maria Garcia-Valdecasas Bernal & Peter Schlenker. A Version rUnversioned. Built using pdfL TEX. Permission is granted to copy, distribute and/or modify this document under the terms of the GNU Free Documentation License, Version 1.2 or any later version published by the Free Software Foundation; with no Invariant Sections, no Front-Cover Texts, and no Back-Cover Texts. A copy of the license is included in the section entitled “GNU Free Documentation License”. The Rockbox manual (version rUnversioned directory-140722) Ipod Nano

• USER GUIDE PROFESSIONAL MICROPHONE iPod

Working with the audio application experts at Audiofile Engineering, Blue has developed its own recording software app, Blue FiRe, specifically tailored to bring the most out of your Mikey. You can find it available for free download in the App Store. Blue FiRe for Mikey provides CD-quality stereo recording capabilities along with basic file management capabilities and simple touch-screen editing for the iPod Touch. • iPod touch (1st, 2nd, and 3rd generation) • iPod nano (2nd, 3rd, 4th, and 5th generation) • iPod classic • iPod (5th generation) The iPod touch allows you to expand Mikey’s capabilities with a wide range of new recording apps, all available for download from the App Store. Note that there are many recording applications available, and all should properly address and record with Mikey. However, some programs may hinder Mikey’s capabilities (like the built in Voice Recorder app, which only records only low quality, mono audio), so be sure to download and use Blue FiRe so your recordings will have all the quality they deserve. You can also check out Blue’s Mikey web page for a more complete listing of available recording apps and their capabilities. 4 5 QUICK START GUIDE • iPod touch (Blue FiRe) • Connect Mikey to the bottom of the iPod touch, with the Blue logo facing up (the same direction as your iPod touch Screen).

Product Guide - Sonos
by Ijimura 0 Comments favorite 4 Viewed Download 0 Times

No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including but not limited to photocopying, recording, information retrieval systems, or computer network without the written permission of Sonos, Inc. SONOS and all other Sonos product names and slogans are trademarks or registered trademarks of Sonos, Inc. SONOS Reg. U.S. Pat. & Tm. Off. Sonos products may be protected by one or more patents. Our patent-to-product information can be found here: sonos.com/legal/patents iPhone®, iPod®, iPad® and iTunes® are trademarks of Apple Inc., registered in the U.S. and other countries. Windows® is a registered trademark of Microsoft Corporation in the United States and other countries. Android® is a trademark of Google, Inc. MPEG Layer-3 audio decoding technology licensed from Fraunhofer IIS and Thomson. Sonos uses MSNTP software, which was developed by N.M. Maclaren at the University of Cambridge. © Copyright, N.M. Maclaren, 1996, 1997, 2000; © Copyright, University of Cambridge, 1996, 1997, 2000. All other products and services mentioned may be trademarks or service marks of their respective owners. March 2014 ©2004-2014 by Sonos, Inc. All rights reserved. SONOS DOCK • Allows you to play your favorite music from an iPod® or iPhone® on a Sonos system—all throughout your home. The DOCK is compatible with*: • iPod touch (1st, 2nd 3rd, and 4th generation) • iPod classic • iPod nano (3rd, 4th, 5th and 6th generation) • iPhone 4, iPhone 4S, iPhone 3GS • iPhone 3G, iPhone • Charges while it’s seated in the DOCK. The DOCK supports 1 Amp charging, the latest specification from Apple®. • Great for parties—simply have your friends dock their iPod or iPhone for play back on your Sonos system. * For the latest system requirements or compatible audio formats, go to http://faq.sonos.com/specs.

P75146_F8Z075 TuneFM iPod mnl.indd - Belkin

Congratulations and thank you for purchasing the innovative TuneFM from Belkin. This product is designed to play your iPod through your car, home, or portable stereo. Please review this User Manual carefully so that you can be sure to get the most from your iPod, virtually anywhere you go. Package Includes: Plastic Spacer (for use only when your iPod is not in a case) TuneFM for iPod Auto Power Cord Introduction | 01 Car Setup Instructions 1. Turn down your car stereo’s volume. 2. Connect the Belkin TuneFM to your iPod (at the bottom of the iPod). 3. Connect the included Auto Power Cord to your cigarette-lighter outlet in your car and to the bottom of your TuneFM for optional powering and charging in the car. Car Setup Instructions | 02 Using the TuneFM Transmitter The TuneFM transmitter function automatically turns on when the iPod is connected. It automatically turns off when the iPod is removed. 1. Tune your stereo frequency to a channel with a weak broadcast signal. The ideal channel is one that is not broadcasting a radio program, or is doing so weakly. 2. Insert the TuneFM into your iPod. The iPod backlight will turn on and the current transmitter frequency will be displayed on the iPod screen. 3. Press the ▲ or ▼ button on the TuneFM to select the transmission frequency chosen in step 1. The frequency will be visible on the iPod’s screen. Pressing and holding either button will provide faster tuning. 4. After displaying the current frequency for five seconds, the iPod screen will return to the iPod Main Menu. This happens whenever you make changes to the TuneFM’s settings. All settings—including transmission frequency, volume-control setting, and stereo/mono-control settings—are permanently stored in memory at this time. Note: iPod playback will pause momentarily when entering and exiting the TuneFM control menu. Playback will quickly resume.

« previous  123456789