Found 4089 related files. Current in page 1
PERFOMANCE BOOST The Freescale* MPXV4115V pressure sensor is the ideal part for automotive vacuum sensing needs such as those found in the brake booster application. Prepared by Marc Osajda Automotive Sensor Marketing Motorola – Toulouse, France Advanced braking systems are becoming increasingly common in today’s automobiles. Higher level systems and technology now being used in “brake assist systems” (BAS) in several European cars, have made it possible for more efficient and intelligent braking systems. A key functional application block found in these braking systems that has advanced with this technology surge, is the vacuum brake booster function. Here are a few driving factors behind the need and use of the brake booster, which helps ensure a safer braking system. Independent Systems: In current gasoline engine cars, the engine’s intake manifold generates the vacuum for the brake booster. This system works fine with one exception. The amount of vacuum in the brake booster is unknown by the braking system. Thus the amount of amplification is also unknown. If heavy braking is needed, there is no possibility for the brake system to interact with the intake manifold if additional amplification is required. The manufacturer’s interest for having the vacuum generated by an auxiliary vacuum pump is that the brake system can manage the amount of vacuum as required, on demand. This in turns gives it the ability to perform amplification on its own, giving it complete independent from the engine’s operating condition. The auxiliary pump is also able to provide higher amounts of vacuum whenever necessary. In situations calling for heavy braking, the pressure will naturally decrease in the brake booster, also causing a decrease in the amplification during braking. With an external pump it is possible to maintain, or even increase the amplification during a heavy braking phase. Smart Safety: Wheel blocking due to high-braking force is controlled by the Anti-Lock Brake System (ABS). However, it has been observed that in many cases, drivers do not...
Tube Replacement Instructions: CL/CLM & HECL/HECLM Models Bryan Steam, the originator and leader in the production of ﬂexible tube water and steam boilers for over 90 years, is pleased to provide you with the technical and service information you need to keep your Bryan Boiler running. These instructions will give you the information you need to remove and replace tubes on a CL/CLM or HECL/HECLM Model Bryan Boiler. Here are a few points to consider when inspecting your boiler. 1. Inspect your boiler annually to ﬁnd and replace bad tubes. 2. These are the two warning signs that a tube is bad: • A knocking sound in the tube bank of the boiler indicates a possibly clogged tube. • A white ash visible along the bottom of a tube or tubes indicates that the tube is getting too hot from reduced water ﬂow. Required Tools for Tube Replacement: 1" tube puller 1" tube driver 50/50 mixture pipe dope and cutting oil 1" paint brush 3 lb. hammer 9/16" socket wrench half round ﬁle full round ﬁle piece of emery cloth a tool to bend the tube studs (or small socket/ratchet set) ...
March 1997 ICF Incorporated Fairfax, VA BACKGROUND For the purposes of this survey, a flexible pipeline is defined as a pipeline constructed of flexible material that can be installed in single long runs without the necessity of regular joints either to extend the length of the line or change directions. This material is usually shipped in rolls that are hundreds of feet long, with the installer cutting lengths to fit the requirements of each installation. Most varieties of flexible piping are available with secondary containment either as an option or an integral part of the primary piping. In all cases, the secondary containment piping will not serve as primary piping. The secondary containment piping is designed to channel leakage back to a sump or monitor point, where it can be detected. Because these pipelines differ significantly from the more traditional steel and fiberglass reinforced plastic (FRP) pipelines, the U.S. Environmental Protection Agency (EPA) has periodically requested a survey of their characteristics and availability. This is the third installment of this survey.1
The indictment of nine alleged participants in a fraud scheme that involved infecting thousands of business computers with Zeus malware to steal millions of dollars shows that the malware remains a formidable ongoing threat, financial services security experts say. The victims in the case included a Nebraska bank and a Nebraska company, according to an announcement of the indictment from federal prosecutors. The indictment was unsealed in connection with the April 11 arraignment of two Ukrainian nationals, who were recently extradited from the United Kingdom. Three other Ukrainians and a Russian have not yet been arrested; the indictment also names three other "John Doe" defendants.
The latest 3.4 litre version of the Powertec RP V8 Doubled up Tom Sharp investigates a cost effective V8 racing engine on behalf of Powertec. It essentially consists of a pair of Hayabusa engines, arranged at a 72° bank angle, driving a common crankshaft and mounted to a dedicated dry-sumped crankcase. The result is a P keenly priced V8 engine that is very light, powerful and reliable. The having initially a 2.6 litre displacement, it had been commissioned by been joined by three other varieties (see Table 1), which demonstrates Radical Motorsport for installation into that company’s SR8 sports-racing just how much flexibility is in the base package. The numbers tell the car. Radical specialised in motorcycle-engined sports-racers and was story of commercial success well enough. Powertec have to date built keen to augment its popular four cylinder machines with a V8. a total of 110 RP engines (including 75 RPAs and 25 RPBs); volumes owertec Engineering’s innovative, Suzuki Hayabusa-based engine is now owned, manufactured and built by Powertec Engineering RP V8 engine was introduced in the UK at the Autosport from its base in Peterborough, England. Run by former motorbike International show back in January 2005 since when it engine tuning specialist Ted Hurrell, Powertec employs 14 people in a has been a resounding technical and commercial success. 3000 sq ft factory. Founded upon a pair of 1.3 litre Hayabusa I4 motorcycle engines and The RP was designed and detailed by Steve Prentice of SPD Ltd 68 The original 2.6 litre RPA and the subsequent 2.8 litre RPB have now which any bespoke engine manufacturers would be proud of. However, DOSSIER : POWERTEC RP V8 ENGINE RP V8 CAD image governs UK motorsport – they banned it on the grounds of it not being derived from a passenger-carrying vehicle. Horne’s solicitors eventually ensured the car received its required log book but the MSA made it clear that the RP was not welcome in rallying. Powertec’s original product portfolio plan had included a 2.0 litre ‘screamer’ version, but as Ted Hurrell explains customer demand drove the capacity in the opposite direction. “The screamer was originally conceived for use in 2.0 litre hillclimb and VdeV sportscar racing, however the VdeV regulations quickly changed to insist upon four cylinder car engines and our hillclimb customers went in the direction of the unlimited classes, which means increasing swept volume as far as possible to maximize torque. So only one 2.0 litre engine was built before that variant was then unfortunately the RP series only represents 20% of Powertec’s business; the majority revolves around building and tuning the Suzuki Hayabusa four cylinder shelved. “Those two examples, of the 2.5 and 2.0 litre engines go to engines for markets such as motorbike racing, low volume production...
Parts List Power Commander USB Cable CD-ROM Installation Guide Power Commander Decals Dynojet Decals Velcro® Strip Alcohol Swab Wire tap O2 eliminator The ignition MUST be turned OFF before installation! YOU CAN ALSO DOWNLOAD THE POWER COMMANDER SOFTWARE AND LATEST MAPS FROM OUR WEB SITE AT: WWW.POWERCOMMANDER.COM PLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION 2191 Mendenhall Drive 20-008 www.powercommander.com North Las Vegas, NV 89081 (800) 992-4993 www.powercommander.com 2009 Suzuki Hayabusa PCV - 1 POWER COMMANDER V INPUT ACCESSORY GUIDE A C C E S S O RY I N P U T S Map - The PCV has the ability to hold 2 different base maps. You can switch on the fly between these two base maps when you hook up a switch to the MAP inputs. You can use any open/close type switch. The polarity of the wires is not important. When using the Autotune kit one position will hold a base map and the other position will let you activate the learning mode. When the switch is “CLOSED” Autotune will be activated. Shifter- These inputs are for use with the Dynojet quickshifter. Insert the wires from the Dynojet quickshifter into the SHIFTER inputs. The polarity of the wires is not important. Speed- If your application has a speed sensor then you can tap into the signal side of the sensor and run a wire into this input. This will allow you to calculate gear position in the Control Center Software. Once gear position is setup you can alter your map based on gear position and setup gear dependent kill times when using a quickshifter. USB CONNECTION CRANK ANALOG EXPANSION PORTS 1 & 2 Optional Accessories such as Color LCD unit or Auto tune kit.
RCC Turbos - Stage 1 Turbo Install: Suzuki Hayabusa (Gen 1) • Preparation/Disassembly: Remove the seat. Disconnect negative terminal on the battery. Drain the fuel tank. Remove the fuel tank. Remove the stock fuel pump from the tank. Remove the air box. Remove the MAP sensor and temperature sensor from the air box. Remove left and right side fairings. Drain engine oil. Drain engine coolant. Remove the oil filter Remove the oil restrictor, behind the filter. Remove the oil cooler lines. Remove the radiator and oil cooler, as one unit, leaving only the bracket/support for radiator (before reinstalling the radiator please remove all the tabs along the bottom of the radiator). Remove the entire exhaust system. Remove the PAIR system. Remove the oil pan from the engine. • Sensor Bracket Modification: On the left hand side of bike, on the inside of the frame, you will see a bracket, with a plastic vacuum canister, vacuum control solenoid valve, atmospheric pressure sensor, and some vacuum lines, with a check valve in the vacuum line. Please remove this entire bracket, eliminate all the vacuum lines, the plastic canister, and the control solenoid valve, and also cut off the metal tab that held the vacuum canister. Then reinstall this bracket with only the atmospheric pressure sensor, and plug the wires back in. • Tap/plug PAIR System Holes: Tap the four small PAIR system holes, above the exhaust ports, with an M6 x 1.0 tap. Install the four small M6 screws into the exhaust holes after tapping them. • Modify the Oil Pan: Drill a ¾” hole on the left side of the oil pan. Use thread sealant on the washer, and red Loctite on the threads. Make sure the sealing washer is against the inside of pan, then the stainless flat washer, then the nut. Once the fitting is installed, reinstall the oil pan. • Install Header/Turbo/Oil Lines/Exhaust: Install the header and turbo as a unit, but with the bolts loose. Use four of your original header bolts on the top of the turbo header (Allen head). Use the four new bolts on the bottom row of the header (M8, 10mm flange head). PLEASE NOTE! After installing the dump pipes and waste gate, the nipple on the top of the waste gate remains open, and no hose gets installed on the top fitting. The top fitting is used for boost control on Stage 2 and higher end kits. It is not used on Stage 1 kits.
Functional Resume Sample John W. Smith 2002 Front Range Way Fort Collins, CO 80525 firstname.lastname@example.org Career Summary Four years experience in early childhood development with a diverse background in the care of special needs children and adults. Adult Care Experience Determined work placement for 150 special needs adult clients. Maintained client databases and records. Coordinated client contact with local health care professionals on a monthly basis. Managed 25 volunteer workers. Childcare Experience Coordinated service assignments for 20 part-time counselors and 100 client families. Oversaw daily activity and outing planning for 100 clients. Assisted families of special needs clients with researching financial assistance and healthcare. Assisted teachers with managing daily classroom activities. Oversaw daily and special student activities. Employment History 1999-2002 1997-1999 1996-1997 Counseling Supervisor, The Wesley Center, Little Rock, Arkansas. Client Specialist, Rainbow Special Care Center, Little Rock, Arkansas Teacher’s Assistant, Cowell Elementary, Conway, Arkansas Education University of Arkansas at Little Rock, Little Rock, AR • • • • BS in Early Childhood Development (1999) BA in Elementary Education (1998) GPA (4.0 Scale): Early Childhood Development – 3.8, Elementary Education – 3.5, Overall 3.4. Dean’s List, Chancellor’s List
SAMPLE RESUME FORMAT Although the Federal Government does not require a standard application form for most jobs, we do need certain information to evaluate your qualifications and determine if you meet legal requirements for Federal employment. If your resume or application does not provide all the information requested in the job vacancy announcement you may lose consideration for a job. WHAT TO INCLUDE Job Information Announcement number, title and grade of the job you are applying for Personal Information Full name, mailing address (with Zip Code) Day and Evening phone numbers Email Country of Citizenship Veterans’ Preference Reinstatement eligibility (Proof of your career or career conditional status may be requested) Highest Federal civilian grade held (provide job series and dates held) Desired Location(s) Work Experience Provide information for your paid and nonpaid work experience related to the job you are applying for. Job Title (include series and grade if Federal job) Job Address Duties and accomplishments Employer’s name and address Starting and ending dates (month and year) Hours per week Salary Supervisor’s name and phone number Indicate if we may contact your current supervisor. Education High School o Name, City, and State o Date of diploma or GED Colleges or Universities o Majors o Name, City, and State o Type and year of any degrees received o If no degree, show total credits earned and indicate whether semester or quarter hours.) A copy of your college transcript may be requested if you are using education to meet qualification requirements. An official transcript will be required prior to your appointment if selected.