SEARCH

Found 6950 related files. Current in page 1

1996 toyota 4runner 3 4 liter engine coolant lines diagram

Technical Bulletin - JASPER Engines & Transmissions

Interference Between Clutch Damper and Flywheel Bolts On 2003-2006 Caterpillar 3406E C-15 & C-16 Diesel Engines The AERA Technical Committee offers the following information regarding possible interference between the clutch damper and flywheel bolts on 2003-2006 Caterpillar 3406E, C-15 and C-16 diesel engines. Engines built or serviced with the VCT plus clutch damper, introduced in April 2003, have the possibility of the clutch damper interfering with the flywheel mounting bolts. This applies to the following clutch part numbers: 108009-32Y, 108925-20, 108925-25, 108926-20Y, 108926-25Y, 109701-20, 109701-25, 109705-20Y, 109705-25Y & 109706-32Y. Correction/Action: Any repair that has required the transmission to be removed from the truck, and the engine serial number is 5EK1 and up, 6TS1 and up, 1LW1 and up, 2WS1 and up, 6NZ1-92122, 7CZ1-04382, MBN1-21447, BXS1-00984, 5DS1 and up, or 1MM1 and up, requires checking the flywheel bolt washers. You must verify the 5mm washer has been replaced with the 3mm washer, Caterpillar Part Number 8D-5054. Failure to replace the washers could result in damper rivet interference. Torque the bolts to 270 Nm +/- 40 Nm (200 ft/lb +/- 30 ft/lb). It is also suggested that paint may be applied to bolt heads to show verification and completion identification.

520 CRF 150R and 625 KX 450F 06-08 Flywheel ... - Steahly Offroad

Installation Instructions for CRF 150R and KX450F Steahly Flywheel Weight Warning: Improper instalation of this flywheel weight could result in engine damage or a serious crash. If you do not have the tools or the mechanical abilities take it to a professional. 1. Drain the engine oil or turn off the gas and lay the bike on its side. 2. Remove the shift lever. 3. Remove the ignition cover. Take care not to tear the gasket or have a new gasket on hand. Be carefull that you don’t lose the two dowel pins that are between the cover and the engine case. 4. Remove the flywheel nut. Use an air impact wrench or figure out a way to keep the flywheel from rotating while you remove the nut. A strap wrench or an automotive oil filter wrench may work as a holding tool or try putting the bike in high gear and holding the rear brake on. 5. Pull off the stock flywheel with the proper flywheel puller that has a crank end protection cap. Steahly part number E-63. Do not attempt removal with out the correct puller. Do not use claw type pullers. 6. Fit the flywheel weight on to the stock flywheel. Line up the two threaded holes in the weight with two holes in the stock flywheel. 7. Clean the threads of the two special bolts with contact cleaner. Put a big drop of red Loctite or other high strength thread locker on the threads of the 2 bolts. Install the two special bolts as shown in the picture and torque to 12 foot pounds. 8. Unless you plan to take the weight on and off a lot we highly recommend using a center punch and a hammer to flare out the threads at the end of the bolt (see pictures below). This will reduce the possibility of the bolt coming loose. 9. Clean up the flywheel and weight and remove any metal stuck to the magnets. 10. Install the flywheel with weight back onto the tapered crank shaft end making sure the key ways are lined up. Torque the stock nut to 42 ft- lbs.

18SP666 – MBE 900 Pilot Bearing Bolt Service Kit (P/N ... - DDCSN

New flanged multi-point socket head bolts have been released to prevent the MBE 900 pilot bearing from walking out of the flywheel housing. The new bolts will replace two flywheel bolts, located 180 degrees from one another. KIT CONTENTS The MBE 900 Pilot Bearing Bolt Service Kit P/N: A9269900105, consists of the following parts, listed in Table 1: Part No. A9269900005 18SP666 Table 1 Qty. 2 1 Description Flanged Multi-point Socket Head Bolts Installation Instructions MBE 900 Pilot Bearing Retaining Bolt Service Kit (P/N: A9269900105) INSTALLATION PROCEDURE Use the following procedure to install the new flanged multi-point socket bolts: 1. Shut off engine and apply the parking brake, chock the wheels, disconnect vehicle battery power, and perform any other applicable safety steps. 2. Remove the transmission. 3. Remove clutch from flywheel. 4. Pull the crankshaft position sensor out of the flywheel housing about 8 mm (0.32 in.). 5. Remove the end cover from the flywheel housing and install the engine barring tool (J-46392). Tighten the bolts on the barring device to 25 N·m (18 lb·ft). Insert the locking pin to block the device and prevent it from rotating. 6. Using J-46385, the flywheel and main pulley socket tool, remove two flywheel multi-point socket head bolts from the flywheel, 180 degrees apart. See Figure 1.

1.9 CRANKSHAFT ASSEMBLY - DDCSN
by Prezta 0 Comments favorite 6 Viewed Download 0 Times

The crankshaft is precision-forged with seven main bearings and eight custom-forged counter weights, and a vibration damper at the front end. For an exploded view of the crankshaft, main bearings, and main bearing caps, see Figure 1-42. 1. Crankshaft 5. Lower Bearing Shell (center) 2. Upper Bearing Shell(s) 6. Main Bearing Cap(s) 3. Upper Bearing Shell (center) 7. Main Bearing Cap (center) 4. Lower Bearing Shell(s) 8. Main Bearing Cap Bolt Figure 1-42 Crankshaft, Main Bearings, and Main Bearing Caps All information subject to change without notice. (Rev. 3/04) 6SE412 0403 Copyright © 2006 DETROIT DIESEL CORPORATION From Bulletin 1–MBE4000–06 1-57 1.9 CRANKSHAFT ASSEMBLY 1.9.1 Crankshaft Removal Remove the crankshaft as follows: FALLING ENGINE To avoid injury from a falling engine, an adequate lifting device with a spreader bar and sling should be used to lift the engine. The sling and spreader bar should be adjusted so the lifting hooks are vertical to prevent bending the lifter brackets. To ensure proper weight distribution, all provided lifter brackets must be used. NOTICE: A spreader bar must be used at all times in conjunction with the front and rear lifter brackets to lift the EGR engine to ensure that no engine damage will result. The brackets are designed to lift vertically. 1. Remove the engine from the vehicle.

Ultra-High Performance NoSQL Benchmarking - Aerospike

As companies deal with ever larger amounts of data and increasingly demanding workloads, a new class of databases has taken hold. Dubbed “NoSQL”, these databases trade some of the features used by traditional relational databases in exchange for increased performance and/or partition tolerance. But as NoSQL solutions have proliferated and differentiated themselves (into key-value stores, document databases, graph databases, and “NewSQL”), trying to evaluate the database landscape for a particular class of problem becomes more and more difficult. In this paper we attempt to answer this question for one specific, but critical, class of functionality – applications that need the highest possible raw performance for a reliable storage engine. There have been a few attempts to provide standardized tools to measure performance or other characteristics, but these have been hobbled by the lack of a clear mandate on exactly what they’re testing, plus an inability to measure load at the highest volumes. In addition, there is an implicit tradeoff between the consistency and durability requirements of an application and the maximum throughput that can be processed. What is needed is not an attempt to quantify every NoSQL solution into one artificial bucket, but a more systemic analysis of how some of these databases can achieve under assumptions that mirror real-world application needs. We attempted to provide a comprehensive answer to one specific set of use cases for NoSQL databases -- consumer-facing applications which require extremely high throughput and low latency, and whose information can be represented using a key-value schema. In particular, we look at two common scenarios.

Website Maintenance by a SEO Consultant in India

Owning a website is not the end of all. You should ensure that it is maintained well in order to find one of the top slots in a search engine.

Amarok Brochure - Volkswagen
by Shatner 0 Comments favorite 9 Viewed Download 0 Times

Rugged or refined: whatever you need Whether it’s cruising on paved surfaces or heading off-road, the Amarok is equipped to deliver the performance for all environments and terrains D riv ing te ch ex pla ine d Permanent 4MOTION® Permanent is great for convenient off-roading. It keeps the four-wheel-drive system engaged whether you’re on- or off-road, so that power is always sent to the wheels with the most oned on South America’s rough mountain Sure-footed on any terrain grip. It’s available on the terrain, it’s no surprise that the Amarok is Designed to tackle the toughest off-road terrains, Amarok Highline – the such a formidable off-roader. With its powerful the Amarok has an Electronic Stabilisation Programme manual model comes with 2.0-litre TDI engines and the dynamic all-terrain benefits (ESP) fitted as standard – part of an impressive range the standard leaf-spring of the intelligent 4MOTION four-wheel-drive, it will take of safety features, which include on- and off-road suspension. The automatic you anywhere you need to go. On-road performance is anti-lock braking systems, an Electronic Differential has the heavy-duty leaf just as composed, thanks to the Amarok’s refined ride. Lock, and Trailer Stability Control. suspension system. Dependable four-wheel drive steep inclines when pulling away, while Hill Descent Selectable At the heart of the Amarok’s off-road performance is Control regulates engine speed and applies the brakes 4MOTION® Selectable Volkswagen’s advanced 4MOTION system, which if necessary, so that you can drive down slopes in a safe is ideal for rugged helps maintain optimum traction on all road surfaces.

VW Amarok - Body Harness.pdf - Hayman Reese

For P/No: 04998 & 04999 only. 1. In the engine bay, disconnect the negative and positive battery terminals. 2. Remove the vehicle battery (1) by first removing any fasteners. 3. Locate the vehicle grommet behind the battery cavity area. 4. Pierce a hole in the vehicle grommet. Note: Do not connect the harness to the battery at this point. Issue Date 27-09-10 For P/No: 04997 only. 5. In the engine bay, locate the vehicle battery (1). 6. Route the body harness (2) down through to the chassis. Note: Do not connect the harness to the battery at this point. 7. Route the power input harness (1) from the engine bay down through to the chassis, following the path of the brake and fuel lines. For P/No: 04997 & 04999 only. 8. Following the diagram on the right, house the two power & ground input harness female terminals (4) into the mating connector (3). 9. Connect the power input harness connector (3) to the body harness mating connector. Issue Date 27-09-10 For P/No: 04998 only. 10. Following the diagram on the right, house the three power & ground input harness female terminals (4) into the mating connector (5). 11. Connect the power input harness connector (5) to the body harness mating connector. 12. Route the body harness (1) along the LHS chassis rail, following the path of the blue vehicle harness towards the rear of the vehicle. 13. Route the body harness (1) along the rear of the vehicle towbar towards the towbar mounting bracket. Issue Date 27-09-10

TROllEy JAck 2TONNE WITh cARRy/ sTORAGE cAsE - Sealey

 Ensure the jack is in sound condition and good working order. Take action for immediate repair or replacement of damaged parts. Use genuine parts only. The use of improper parts may be dangerous and will invalidate the warranty. Locate the jack in a suitable, well lit working area. Keep working area clean and tidy and free from unrelated materials. Use jack on level and solid ground, preferably concrete. Avoid tarmacadam as jack may sink in. Place wedges under wheels of vehicle, but ensure the jack wheels are free to move and that there are no obstructions. Ensure the vehicle handbrake is engaged, engine is switched off and transmission is in gear (or “PARK” if automatic). Ensure minimum distance of 0.5m between vehicle and static objects such as doors, walls, etc., to allow for vehicle tilting. Ensure there are no passengers in the vehicle and that all non-essential persons keep a safe distance whilst the jack is in use. Place jack under lifting points recommended by vehicle manufacturer (see vehicle hand book). Ensure lifting point is stable and centred on saddle.  WARNING! When lifting at the jack's maximum rating (2tonne) or close to it, it is recommended that the effort of raising the load shall be reduced by the use of assistance during this operation.  ANGER: Use the jack for lifting only, NOT for supporting the lifted load.

TROLLey JACKS - Sealey
by Dockyard 0 Comments favorite 0 Viewed Download 0 Times

 Ensure that the jack is in sound condition and good working order. Take action for immediate repair or replacement of damaged parts. Use recommended parts only. Unapproved parts may be dangerous and will invalidate the warranty.  Locate the jack in an adequate, well lit work area.  Keep work area clean and tidy and free from unrelated materials.  Use jack on level and solid ground, preferably concrete. Avoid tarmacadam as jack may sink in.  Place wedges under the wheels of the vehicle but ensure that the wheels of the jack can move freely.  Ensure that the vehicle handbrake is engaged and switch off the engine.  Ensure a minimum distance of 0.5m between vehicle tilt and static objects such as doors, walls, etc.  Ensure all non-essential persons keep a safe distance whilst the jack is in use.  Ensure that there are no passengers in the vehicle to be jacked up.  Place jack under vehicle manufacturer’s recommended lifting points (see vehicle handbook).  Check that the lifting point is stable and centred on the jack saddle.  Ensure that the jack wheels are free to move and that there are no obstructions.  IMPORTANT! During the jacking operation ensure that you can always see the vehicle-to-jack 

« previous  123456789