SEARCH

Found 1781 related files. Current in page 1

1992 harley fxdc wiring diagram

VW Amarok - Body Harness.pdf - Hayman Reese

For P/No: 04998 & 04999 only. 1. In the engine bay, disconnect the negative and positive battery terminals. 2. Remove the vehicle battery (1) by first removing any fasteners. 3. Locate the vehicle grommet behind the battery cavity area. 4. Pierce a hole in the vehicle grommet. Note: Do not connect the harness to the battery at this point. Issue Date 27-09-10 For P/No: 04997 only. 5. In the engine bay, locate the vehicle battery (1). 6. Route the body harness (2) down through to the chassis. Note: Do not connect the harness to the battery at this point. 7. Route the power input harness (1) from the engine bay down through to the chassis, following the path of the brake and fuel lines. For P/No: 04997 & 04999 only. 8. Following the diagram on the right, house the two power & ground input harness female terminals (4) into the mating connector (3). 9. Connect the power input harness connector (3) to the body harness mating connector. Issue Date 27-09-10 For P/No: 04998 only. 10. Following the diagram on the right, house the three power & ground input harness female terminals (4) into the mating connector (5). 11. Connect the power input harness connector (5) to the body harness mating connector. 12. Route the body harness (1) along the LHS chassis rail, following the path of the blue vehicle harness towards the rear of the vehicle. 13. Route the body harness (1) along the rear of the vehicle towbar towards the towbar mounting bracket. Issue Date 27-09-10

Trolley Jacks - Supplier Guide - ACCC

Australian Competition and Consumer Commission 23 Marcus Clarke Street, Canberra, Australian Capital Territory, 2601 © Commonwealth of Australia 2013 This work is copyright. In addition to any use permitted under the Copyright Act 1968, all material contained within this work is provided under a Creative Commons Attribution 3.0 Australia licence, with the exception of: • the Commonwealth Coat of Arms • the ACCC and AER logos • any illustration, diagram, photograph or graphic over which the Australian Competition and Consumer Commission does not hold copyright, but which may be part of or contained within this publication. The details of the relevant license conditions are available on the Creative Commons website, as is the full legal code for the CC BY 3.0 AU licence. Requests and inquiries concerning reproduction and rights should be addressed to the Director, Internal Communication and Publishing Services, ACCC, GPO Box 3131, Canberra ACT 2601, or publishing.unit@accc.gov.au. Important notice The information in this publication is for general guidance only. It does not constitute legal or other professional advice, and should not be relied on as a statement of the law in any jurisdiction. Because it is intended only as a general guide, it may contain generalisations.

Gateway Lite BT install guide - Dension

Gateway Lite BT enables music playback from a USB storage or iPod through your vehicle’s entertainment system, using the buttons of the car stereo for basic control. Once the head unit has been removed, disconnect the antenna cable (1) and then unclip the main wiring connector from the head unit (2). This will differ in all makes and manufacturers. This device also offers handsfree mobile call handling via the original buttons of the Head Unit (Radio). Connect the 12 way micro-fit (12 pin molex) to the Car side of the Gateway Lite BT module. The Dension Gateway Lite BT is available in specific versions for different vehicle types, therefore the exact operation and installation may be different in each case. Warning! Do not trap the cables, or leave them in a position where they may become trapped after refitting the head unit. Ensure the device is correctly fitted before running the cable. Then, reconnect the Dension supplied main radio connector to the rear of the head unit. Gateway Lite BT is designed to give easy to manage control, in cars where it is not possible to display text, therefore only basic control is available (track skip functions and USB folder browsing). At first please make sure that the vehicle compatibility is correct. Connect the round iPod connector and USB to the module and feed them through the dashboard to an appropriate location. With the main radio cable removed, first connect the Dension supplied cable to the original factory cable harness.

A Brief History Of Motorcycle Patches

http://www.artexgroup.net | Motorcycle patches are used to establish identity and rank in the motorcycle community. Custom patches, including Harley custom patches, are a great way to show individuality or establish an identity for your organization.

Steering, Suspension, and Driveline Basics (with How Lift ... - Meetup

Throughout this article I will address many basics of your vehicle’s steering, suspension, driveline, tires, and wheels. I did not intend this to be a “how to” manual with step by step instructions. It will simply illustrate the concepts. I’ll start with the lift and explain what it did to your steering, suspension, and driveline one aspect at a time. NOTES ABOUT THE ILLUSTRATIONS: 1) most are “spring under” leaf spring suspension, 2) non-pertinent parts are omitted for clarity, 3) many examples are exaggerated for illustration, and 4) most concepts illustrated also apply to spring over and coil/link suspensions. To cover the differences, I added a separate coil and link suspensions topic. Ready? OK, let’s get started. You lifted your Jeep and now it wanders all over the road and it vibrates too. What happened? Well, you just changed a lot of the vehicle’s geometry (probably without knowing it). Here’s a diagram of a stock Jeep and the proper angles. Your caster angle should be between 4 and 8 degrees positive. This caster angle creates an effect called mechanical trail. It’s the force that makes your wheels return to center. The caster angle shown below is close to stock. The point that the steering axis (black line) intersects the ground to the point to where the rotational axis touches the ground forms the points to measure your caster angle. You can best measure the caster angle from the top of the upper ball joint.

1 TON FOLDING ENGINE STAND - Harbor Freight Tools

1 TON FOLDING ENGINE STAND Model 47304 ASSEMBLY AND OPERATING INSTRUCTIONS ® 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our Web site at http://www.harborfreight.com Copyright © 2002 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools . For technical questions and replacement parts, please call 1-800-444-3353 Specifications Engine Stand Capacity Assembled Dimensions Folded Dimensions Engine Turn Capacity Main Post Height 1 Ton (2000 Lbs.) 42” L x 36” W x 34” H 17” L x 22-1/2” W x 40” H 360 Degrees 32-1/2” Save This Manual You will need the manual for the safety warnings and precautions, assembly instructions, operating and maintenance procedures, parts list and diagram. Keep your invoice with this manual. Write the invoice number on the inside of the front cover. Keep the manual and invoice in a safe and dry place for future reference. Safety Warnings and Precautions WARNING: When using product, basic safety precautions should always be followed to reduce the risk of personal injury and damage to equipment. Read all instructions before using this product! 1. Avoid working alone. If an accident happens, an assistant can bring help. 2. Keep work area clean. Cluttered areas invite injuries. 3. Observe work area conditions. Don’t expose to rain. Keep work area well lighted. 4. Keep children away. Children must never be allowed in the work area. Do not let them near the Stand. 5. Store idle equipment. When not in use, the Stand must be stored in a dry location to inhibit rust. Always lock up tools and keep out of reach of children. 6. Dress properly. Do not wear loose clothing or jewelry as they can be caught in moving parts. Protective, electrically nonconductive clothes and nonskid footwear are recommended when working. Wear restrictive hair covering to contain long hair. 7. Use eye and ear protection. Always wear ANSI approved impact safety goggles. 8. Do not overreach. Keep proper footing and balance at all times. Do not reach over or across electrical cables or frames. 9. Maintain Stand with care. Inspect Stand, and if damaged, have it repaired by an authorized technician. SKU 47304

AXLE SHAFTS - FRONT Article Text - Webs

Power from transaxle is transferred to driving wheels by 2 axle shafts. Both axle shafts use Constant Velocity (CV) joints at inner and outer ends. CV joints are enclosed in CV boots, and connected by an intermediate shaft. Intermediate shaft is splined on both ends. Retaining rings retain intermediate shaft in the inner and outer CV joints. A retaining ring retains inner CV joint stub in differential side gear. Outer CV joint stub is splined into wheel hub, and secured by a spindle nut. Left axle has a dynamic damper to reduce vibration. The following are possible types of Constant Velocity (CV) joints used on axle shaft: Birfield Joint (BJ), Double Offset Joint (DOJ), Rzeppa Joint (RJ) and Tripod Joint (TJ). Determine type of CV joint used prior to disassembly. See AXLE SHAFT SPECIFICATIONS table under INSTALLATION. Note type of boot and location prior to removal. See BAND & BOOT APPLICATION. Install a NEW retaining ring each time axle shaft is removed from transaxle. Article Text (p. 3) 1992 Mitsubishi Mirage For Dan's Transmission Service 10 Jefferson Place Fort Walton Beach FL 32548 © 1997 Mitchell Repair Information Company, All Rights Reserved. Monday, April 01, 2002 09:00AM

3.0 L V6 - VINS [H,J,K] - dairally.net

Removal (Diamante) 1) Remove hood. Drain cooling system. Remove radiator. Release fuel system pressure. See FUEL PRESSURE RELEASE. Disconnect negative battery cable. Drain engine oil and transaxle oil. Remove front exhaust pipe. Remove transaxle assembly. See appropriate CLUTCHES or TRANSMISSION SERVICING article. 2) Disconnect accelerator cable, brake booster vacuum hose, fuel supply and return lines, and heater hoses. Disconnect EGR temperature sensor (if equipped). Unplug vacuum hose connector. Remove drive belts. Remove power steering pump and A/C compressor, leaving hoses attached. 3) Unplug all harness connectors. Remove bolt from body ground connection. Disconnect alternator wiring inside relay box. Remove relay box and engine wiring harness connection. On models with ABS, remove radiator overflow tank and bracket. 4) Attach engine hoist. Raise engine enough to take weight from mounts. Remove engine mount bracket. Remove damper. Remove rear roll stopper bracket mount bolt. Remove front roll stopper bracket mount bolt. Carefully lift engine from car. Installation (Diamante) To install, reverse removal procedure. Install engine mount bracket so that arrow points away from engine, toward body. Install new "O" rings on fuel lines. Install new exhaust gaskets and nuts. Adjust throttle cable. See TORQUE SPECIFICATIONS TABLE at the end of this article. Replenish fluids. CAUTION: DO NOT allow foreign material into turbocharger air intake hoses or pipes.

Printable (PDF) version - Innovate Motorsports

www.tuneyourengine.com. 1994 - 1997 Mitsubishi 3000GT VR4 ECU Diagram. Connector A. Connector B Connector C. Connector D. Pin #. Name. Signal Type. Connector B Name Injector 1 Injector 3 Injector 5 Injector 2 Injector 4 Injector 6 Power Ground Air Intake Temperature Sensor O2 Sensor # 1 (Right Bank) O2 Sensor # 2 (Left Bank) Engine Coolant Temperature Sensor Throttle Position Sensor Atmospheric Pressure Sensor Vehicle Speed Sensor Volume Air Flow Sensor Power Ground Sensor Ground Connector C Connector D Signal Type Speed Speed Speed Speed Speed Speed Ground Analog Analog Analog Analog Analog Analog Speed Analog Ground GroundConnector B Name Injector 1 Injector 3 Injector 5 Injector 2 Injector 4 Injector 6 Power Ground Air Intake Temperature Sensor O2 Sensor # 1 (Right Bank) O2 Sensor # 2 (Left Bank) Engine Coolant Temperature Sensor Throttle Position Sensor Atmospheric Pressure Sensor Vehicle Speed Sensor Volume Air Flow Sensor Power Ground Sensor Ground Connector C Connector D Signal Type Speed Speed Speed Speed Speed Speed Ground Analog Analog Analog Analog Analog Analog Speed Analog Ground GroundConnector B Name Injector 1 Injector 3 Injector 5 Injector 2 Injector 4 Injector 6 Power Ground Air Intake Temperature Sensor O2 Sensor # 1 (Right Bank) O2 Sensor # 2 (Left Bank) Engine Coolant Temperature Sensor Throttle Position Sensor Atmospheric Pressure Sensor Vehicle Speed Sensor Volume Air Flow Sensor Power Ground Sensor Ground Connector C Connector D Signal Type Speed Speed Speed Speed Speed Speed Ground Analog Analog Analog Analog Analog Analog Speed Analog Ground Ground

Suzuki GSX-R1300 / Hayabusa - Fuelpak
by nkono 0 Comments favorite 7 Viewed Download 0 Times

GSX-R1300 / HAYABUSA READ ALL INSTRUCTIONS BEFORE BEGINNING INSTALLATION TOOLS NEEDED - #1 Phillips Screwdriver - 5 mm Allen Wrench - 10 mm Socket Wrench - Less than 1 hour 08-09 Suzuki GSX-R1300 / Hayabusa Fuel Injected Models INSTALLATION INSTRUCTIONS FOR P/N 62009 INTRODUCTION: Congratulations on your purchase of the Fuelpak Fuel Management System for fuel injected Suzuki GSX-R1300 and Hayabusa motorcycles. Please take the time to read the entire instruction manual before attempting to install. DO NOT adjust the Fuelpak until you have thoroughly read the instruction manual and the unit is fully installed. If you have questions, please call (562) 921-0071. SUMMARY: To achieve the optimum performance from your application, it is recommended that you install a high performance air filter in conjunction with this unit. The Fuelpak will be installed in-line the factory injector wiring harness and the throttle position sensor. The Fuelpak will be tucked under the seat next to the ECU with the cables routing to the left side of the motorcycle. PLEASE NOTE: Fuelpak USE REQUIRES A HIGH PERFORMANCE AIR FILTER. 1. Remove the main seat and passenger seat. 2. Use a prop to hold the tank up in the trunk area.

« previous  123456789